The investigation of wear tracks with the use of noncontact measurement methods

• Autorzy: Niemczewska-Wójcik M. , Mańkowska-Snopczyńska A. , Piekoszewski W.
• Języki publikacji: EN

Abstrakty

EN

This article concerns the analysis and evaluation of surfaces previously subjected to tribological research (wear tracks and wear amount), with regard to technological factors and cooperation conditions. The surfaces of discs were the subject of this research made of bearing steel without coating (100Cr6), with antiwear coating (CrN), and with low-wear coating (MoS2). The surfaces were measured before and after tribological studies. The tribological tests were performed on the tribotester T-26 (ball-on-disc contact arrangement) consisting of a bearing steel ball (100Cr6) in contact with a disc. The studies were carried out in a vacuum and in the air. The study of technological surface layer (TWW) and service-generated surface layer (EWW) was made with the use of an atomic force microscope and an interferometer microscope. The obtained results (wear quantity and wear tracks) were analyzed using specialized metrology software. The results obtained with the use of the interferometric microscopy were compared to those obtained by the atomic force microscopy, which enabled comprehensive assessment of the surfaces with respect to material loss (wear).

Słowa kluczowe

EN

coatings; cooperation conditions; surface geometric structure; wear; measurement techniques

PL

powłoki; warunki współpracy; struktura powierzchni; techniki pomiarowe

• Wydawca: Springer ; Wrocław University of Science and Technology
• Czasopismo: Archives of Civil and Mechanical Engineering
• Rocznik: 2013
• Tom: Vol. 13, no. 2
• Strony: 158--167
• Opis fizyczny: Bibliogr. 16 poz., rys., tab., wykr.

Twórcy

autor

Niemczewska-Wójcik M.

• Institute of Production Engineering, Cracow University of Technology, Jana Pawła II No. 37, 31-864 Cracow, Poland

autor

Mańkowska-Snopczyńska A.

• Department of Tribology, Institute for Sustainable Technologies - National Research Institute, K. Puławskiego No. 6/10, 26-600 Radom, Poland

autor

Piekoszewski W.

• Department of Tribology, Institute for Sustainable Technologies - National Research Institute, K. Puławskiego No. 6/10, 26-600 Radom, Poland

Bibliografia

• [1] B. Żółtowski, Machine Diagnostics, Publishing House of University of Technology and Life Sciences in Bydgoszcz, Bydgoszcz, 1996 in Polish.
• [2] P.W. Dong, P.J. Sullivan, K.J. Stout, Comprehensive study of parameters for characterizing three dimensional surface topography, Wear 159 (2) (1992) 161–171.
• [3] V. Lubimov, K.E. Oczoś, Surface Geometric Structure, Publishing House of Rzeszow University of Technology, Rzeszow, 2003 in Polish.
• [4] P. Pawlus, Surface Topography Measurement, Analysis, Influence, Publishing House of Rzeszow University of Technology, Rzeszow, 2006 in Polish.
• [5] K.J. Stout, L. Blunt, Development of Methods for the Characterization of Roughness in Three Dimensions, Penton Press, London, 2000.
• [6] T.R. Thomas, Rough Surfaces, Imperial Collage Press, London, 1999.
• [7] M. Wieczorowski, Surface Topography Analysis, Publishing House of Poznan University of Technology, Poznan, 2009 in Polish.
• [8] B. Nowicki, Measurements of surface roughness, Mechanic 1 (1993) 29–32.
• [9] T.V. Vorburger, Methods for Characterizing Surface Topography, Optical Society of America, Washington, 1992.
• [10] L. Blunt, J. Xiangqiqn (Eds.), Kogan Page Science, London, 2003.
• [11] T. Matnia, H. Zahouani, J. Rousseau, J.C. Le Bosse, Functional significance of different techniques for surface morphology measurements, Machine Tools & Manufacture 35 (1995) 195–202.
• [12] K.J. Stout, L. Blunt, Three Dimensional Surface Topography, Penton Press, London, 2000.
• [13] M. Niemczewska-Wójcik, The influence of the surface geometric structure on the functionality of implants, Wear 271 (3/4) (2011) 596–603.
• [14] M.B. Bauza, S.C. Woody, B.A. Woody, S.T. Smith, Surface profilometry of high aspect ratio features, Wear 271 (3/4) (2011) 519–521.
• [15] A. Mańkowska, W. Piekoszewski, M. Szczerek, The investigation of the friction and wear of antiwear coatings in a vacuum, Tribology Friction, Wear, Lubrication 225 (3) (2009) 125–138.
• [16] Zb. Lawrowski, Tribology Friction, Wear and Lubrication, Publishing House of Wrocław University of Technology, Wrocław, 2009 in Polish.