Mechanical and corrosion properties of Friction Stir Welded and Tungsten Inert Gas welded phosphor bronze

• Autorzy: Gopi S. , Mohan Dhanesh G. , Natarajan Elango

Identyfikatory

DOI

10.2478/adms-2023-0024

• Języki publikacji: EN

Abstrakty

EN

This study investigated the mechanical and corrosion properties of Friction Stir Welded (FSW) and Tungsten Inert Gas (TIG) welded phosphor bronze (CuSn4) joints. Corrosion tests were conducted on the welded joints, and the percentage of weight loss due to corrosion was measured at different time intervals. Results revealed that the percentage of weight loss due to corrosion of the TIG joint increased with time, whereas the percentage of weight loss due to corrosion of the FSW welded joint remained constant. This could be attributed to recrystallisation that happened in the solid-state welding, which reduced corrosion in the FSW welded joint. In addition, tensile tests were conducted to evaluate the strength of the joints. FSW with a spindle speed of 1300 rpm, weld speed of 0.06mm/sec, plunge depth of 0.25mm, pin profile of pentagon, and flat shoulder profile was found to produce good results. TIG welding with a welding speed of 1.75mm/sec, a gas flow rate of 7.5 cm3/min and an amperage of 120A also produced good results. The tensile strength of FSW was found to be approximately 1.6 times higher than that of TIG welding.

Słowa kluczowe

EN

friction stir welding; tig; phosphor bronze; corrosion; tensile strength; welding

PL

zgrzewanie tarciowe z przemieszaniem; TIG; brąz fosforowy; korozja; wytrzymałość na rozciąganie; spawanie

• Wydawca: Politechnika Gdańska
• Czasopismo: Advances in Materials Science
• Rocznik: 2023
• Tom: Vol. 23, nr 4(78)
• Strony: 83--98
• Opis fizyczny: Bibliogr. 66 poz., rys., tab., wykr.

Twórcy

autor

Gopi S.

• Department of Production Engineering, Government College of Technology, Coimbatore, Tamilnadu, India

autor

Mohan Dhanesh G.

• Zhengzhou Research Institute, Harbin Institute of Technology, Zhengzhou, Henan, China

autor

Natarajan Elango

• Faculty of Engineering, Technology and Built Environment, UCSI University, Kuala Lumpur, Malaysia

Bibliografia

• 1. Hu D, Chen M, Wang L, Cheng H: Dynamic tensile behaviour and deformational mechanism of C5191 phosphor bronze under high strain rates deformation. Materials Science and Engineering: A, 2016, 649, 68–73.
• 2. Sanga B, Wattal R, Nagesh D S: Weld joint characterization in ultrasonic welding of phosphor bronze sheets. Engineering Science and Technology, an International Journal, 2022, 30, 101040.
• 3. Velu M, Bhat S: Experimental investigations of fracture and fatigue crack growth of copper–steel joints arc welded using nickel-base filler. Materials & Design, 2015, 67, 244–260.
• 4. Makeshkumar M, Surender S R, Arunprakash S, Madesh R, Sasi Kumar M, Sudharsan K: Microstructural and mechanical properties evaluation of dissimilar aluminum alloy and bronze joints using friction stir welding. Materials Today: Proceedings, 2021, 47, 5239–5244.
• 5. Chaudhary V, Bharti A, Azam S M, Kumar, N, Saxena K K: A re-investigation: Effect of TIG welding parameters on microstructure, mechanical, corrosion properties of welded joints. Materials Today: Proceedings, 2021, 45, 4575–4580.
• 6. Mohan D G, Tomków J, Gopi S: Induction Assisted Hybrid Friction Stir Welding of Dissimilar Materials AA5052 Aluminium Alloy and X12Cr13Stainless Steel. Advances in Materials Science, 2021, 21(3), 17–30.
• 7. Zoeram A S, Anijdan S H M, Jafarian H R, Bhattacharjee T: Welding parameters analysis and microstructural evolution of dissimilar joints in Al/Bronze processed by friction stir welding and their effect on engineering tensile behavior. Materials Science and Engineering: A, 2017, 687, 288–297.
• 8. Mohan D G, Wu C: A Review on Friction Stir Welding of Steels.Chinese Journal of Mechanical Engineering, 2021, 34(1), 137.
• 9. Rabiezadeh A, Salafzon A, Mostafavi N: Dissimilar welding of AA5083/AA7039 by self-reacting friction stir welding. Journal of Adhesion Science and Technology, 2023, 1–22, in Press.
• 10. A M, SS KV, A P K: On the friction stir welding of alloy AA2014 under n-MQL cooling condition. Journal of Adhesion Science and Technology, 2023, 37(13), 2025–2045.
• 11. Sasikumar A, Gopi S, Mohan D G: Prediction of Filler Added Friction Stir Welding Parameters for Improving Corrosion Resistance of Dissimilar Aluminium Alloys 5052 and 6082 Joints. Advances in Materials Science, 2022, 22(3), 79–95.
• 12. Yin, Cao L, Wang N: Mechanical properties and residual stresses of 5083 to AM60B dissimilar friction stir welding with different process parameters. Journal of Adhesion Science and Technology, 2019, 33(23), 2615–2629.
• 13. Anbalagan K, Ramasubramanian S, David C, Manivannan S, Kannan AR, Mohan DG: Importance of shielding and mechanical characterization of GTAW on Ti-6AL-4V alloy sheet. Welding International, 2023, 37(6), 324–333.
• 14. Chen X H, Ma YF, Cheng Y J, Wang Z D, Yang M, Jiang W W, Cao Y D: Strengthening and toughening strategies of weld metal for in-situ nanoparticle reinforced tin bronze alloy. Science and Technology of Welding and Joining, 2021, 26(4), 309–315.
• 15. N V Babu: Fatigue strength of welded joints in complexly alloyed aluminium bronzes. Welding International, 1989, 3(5), 386–388.
• 16. Cheng Z, Liu H, Huang J, Ye Z, Yang J, Chen S: MIG-TIG double-sided arc welding of copper-stainless steel using different filler metals. Journal of Manufacturing Processes, 2020, 55, 208–219.
• 17. Velu M, Bhat S: Metallurgical and mechanical examinations of steel–copper joints arc welded using bronze and nickel-base superalloy filler materials. Materials & Design, 2013, 47, 793–809.
• 18. Poggie R A, Wert J J, Harris L A: The effects of surface oxidation and segregation on the adhesional wear behavior of aluminum—bronze alloys. Journal of Adhesion Science and Technology, 1994, 8(1), 11–28.
• 19. Saraiva A S, Figueiredo E, Águas H, Silva R J C: Characterisation of Archaeological High-tin Bronze Corrosion Structures. Studies in Conservation, 2022, 67(4), 222–236.
• 20. C S Radhika, N Kumar, Sivasailam B: A review on welding techniques: properties, characterisations and engineering applications. Advances in Materials and Processing Technologies, 2023, 1(1), 1–56.
• 21. Nakata K: Friction stir welding of copper and copper alloys. Welding International, 2005, 19(12), 929–933.
• 22. Çam G: Friction stir welded structural materials: beyond Al-alloys. International Materials Reviews, 2011, 56(1), 1–48.
• 23. Mohan D G, Gopi S: Induction assisted friction stir welding: a review. Australian Journal of Mechanical Engineering, 2020, 18(1), 119–123.
• 24. Shokri V, Sadeghi A, Sadeghi M H:Effect of friction stir welding parameters on microstructure and mechanical properties of DSS–Cu joints. Materials Science and Engineering A, 2017, 693, 111–120.
• 25. Squillace A, De Fenzo A, Giorleo G, Bellucci F:A comparison between FSW and TIG welding techniques: Modifications of microstructure and pitting corrosion resistance in AA 2024-T3 butt joints. Journal of Materials Processing Technology, 2004, 152(1), 97–105.
• 26. Liu HJ, Shen J J, Zhou L, Zhao Y Q, Liu C, Kuang L Y: Microstructural characterisation and mechanical properties of friction stir welded joints of aluminium alloy to copper. Science and Technology of Welding and Joining, 2011, 16(1), 92–98.
• 27. Pan Y, Zhang D, Liu H, Zhang Z, Li H, Zhuang L, Zhang J: Reducing welding hot cracking of high-strength novel Al–Mg–Zn–Cu alloys based on the prediction of the T-shaped device. Science and Technology of Welding and Joining, 2020, 25(6), 483–489.
• 28. Srinivasa Rao M, Tangudu S S, Perumalla S, Uppda B R, Yandra C, Kambhampati K:Effect of TIG and FSW welding processes on mechanical properties of Al-4.2Mg-0.6Mn-0.4Sc-0.1Zr alloy. Strojnicky Casopis,2021, 71(2), 299–304.
• 29. Mallipudi S R, Shankar TS, Srikar P, Rao U B, Chandrasekhar Y, Karthikeyan K: Effect of TIG and FSW Welding Processes on Mechanical Properties of Al-4.2Mg-0.6Mn-0.4Sc-0.1Zr Alloy. Strojnícky Časopis - Journal of Mechanical Engineering, 2021, 71(2), 299–304.
• 30. Sejč P, Bucany M, Zifcak P: Properties of FSW and MIG Welded Joints of AlSiMgAluminum Alloy, Strojnicky timetable – Journal of Mechanical Engineering, 2020, 70 (2)pp141 – 152.
• 31. Vinith B, Dharshan S AD, Aravind S, Singh B K: Friction stir welding evolution, hybrid technologies and shoulder shape. International Journal on Interactive Design and Manufacturing (IJIDeM), 2023, 17(4), 1443–1458.
• 32. Khan F N, Junaid M, Hassan A A, Baig M N: Effect of pulsation in TIG welding on the microstructure, residual stresses, tensile and impact properties of Ti-5Al-2.5Sn alloy. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2021, 235(2), 361–370.
• 33. Das P P, Chakraborty S: Optimization of friction stir welding processes using hybrid-taguchi methods: a comparative analysis. International Journal on Interactive Design and Manufacturing (IJIDeM), 2023, 17(3), 1021–1038.
• 34. Sunny K T, Korra N N, Vasudevan M, Arivazhagan B: Parameter optimization and experimental validation of A-TIG welding of super austenitic stainless steel AISI 904L using response surface methodology. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2022, 236(6), 2608–2617.
• 35. Payak V, Paulraj J, Roy B S, Bhargava M, Das P: A review on recent development in aluminium-copper friction stir welding. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2023, 1(3), 09544089231158201.
• 36. Sharma A K, Goyal D, Pabla B S, Saxena K K, Prakash C, Buddhi D: Optimization of friction stir welding parameters for micro alloying of AA6082 alloy. International Journal on Interactive Design and Manufacturing (IJIDeM), 2022, 2960(1).
• 37. Khan N Z, Siddiquee A N, Khan ZA, Badruddin I A, Kamangar S, Maqbool A: Improvement in joint efficiency with high productivity and narrow weld formation in friction stir welding. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2022, 236(2), 383–393.
• 38. Bist A, Saini J S, Sharma V: Comparison of tool wear during friction stir welding of Al alloy and Al-SiC metal matrix composite. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2021, 235(5), 1522–1533.
• 39. Buffa G, Fratini L: Friction stir welding of steels: process design through continuum based FEM model. Science and Technology of Welding and Joining, 2009, 14(3),239–246.
• 40. Sonar T, Ivanov M, Trofimov E, Tingaev A, Suleymanova I: A critical review on solid-state welding of high entropy alloys– processing, microstructural characteristics and mechanical properties of joints. DefenceTechnology, 2023, 168(1), 114–165.
• 41. Wang Q, Zhou X, Wang B, Liu M, Li C, Tan Z, Wu T: Accelerated role of exogenous riboflavin in selective Desulfovibrio desulfuricans corrosion of pipeline welded joints. Bioelectrochemistry, 2023, 153, 108469.
• 42. Dou W, Jia R, Jin P, Liu J, Chen S, Gu T. Investigation of the mechanism and characteristics of copper corrosion by sulfate reducing bacteria. Corrosion Science, 2018, 144:237e48.
• 43. C Razil, A Aangaj: Prediction of relationship between angular velocity to the pitch line velocity (ω/v) on tensile strength of friction stir welded AA2014-T6 Aluminium alloy joints: Angular velocity to pitch line velocity ratio on FSW joints. Forces in Mechanics, 2021, 4, 100036.
• 44. Liu Peng, Li Yajiang, Wang Juan, Geng Haoran: Microstructure characteristics in TIG welded joint of Mg /Al dissimilar materials. Materials Letters, 61, 2007, pp. 1288-1291.
• 45. AC Somasekharan, LE Murr: Characterization of complex, solid-state flow and mixing in the friction-stir welding (FSW) of aluminum alloy 6061–T6 to magnesium alloy AZ91D using color metallography. Journal of Materials Science, 41, 2006, pp. 5365-5370.
• 46. Naga sathwik sridhara S, Chandra siddhardha Allada S, Sharmi Sai, P V Banala, S Subbiah, Marichamy S: Tensile strength performance and optimization of Al 7068 using TIG welding process. Materials Today: Proceedings, 2021, 45, 20(17).
• 47. Yelamasetti B, Adithya G S, Ramadevi R S, Sonia P, Saxena K K, Kumar P N, Eldin S M, Al- kafaji FH K: Metallurgical, mechanical and corrosion behaviour of pulsed and constant current TIG dissimilar welds of AISI 430 and Inconel 718. Journal of Materials Research and Technology, 2023, 24, 6652–6664.
• 48. Tamadon A, Pons D J, Clucas D: Analogue Modelling of Flow Patterns in Bobbin Friction Stir Welding by the Dark-Field/Bright-Field Illumination Method. Advances in Materials Science, 2020, 20(1), 56-70.
• 49. B Yelamasetti, TV Vardhan, GV Ramana: Study of metallurgical changes and mechanical properties of dissimilar weldments developed by interpulse current TIG welding technique. Proceedings of the Institution of Mechanical Engineers - Part C: Journal of Mechanical Engineering Science, 2021, 235 (16), pp. 2985-2997.
• 50. Xuan Y, Yang J, Liu H, Deng J, Wang Y: Microstructure and mechanical properties of Invar36 alloy joints using keyhole TIG welding. Science and Technology of Welding and Joining, 2020, 25(8), 712–718.
• 51. Kumar S A, Sathiya P: Experimental Investigation of the A-TIG Welding Process of Incoloy 800H. Materials and Manufacturing Processes, 2015, 30(9), 1154–1159.
• 52. Dhondt, Matthieu, Aubert, Isabelle, Saintier, Nicolas, Olive, Jean-Marc: Intergranular stress corrosion cracking of friction stir welded nugget on a 2050-T8 aluminum alloy. Advances in Materials Science, 2011, 11(3), 43-50.
• 53. Kusano K, Watanabe H: Recent trends in development of high‐efficiency TIG welding; high‐deposition TIG welding and ultranarrow‐gap TIG welding. Welding International, 2002, 16(12), 986–991.
• 54. Górka J, Przybyła M, Szmul M, Chudzio A, Ładak D: Orbital TIG Welding of Titanium Tubes with Perforated Bottom Made of Titanium-Clad Steel. Advances in Materials Science, 2019, 19(3), 55–64.
• 55. Sridhar SP, Arun Kumar S, Sathiya P: A Study on the Effect of Different Activating Flux on A-TIG Welding Process of Incoloy 800H, Advances in Materials Science, 2022, 16(3), 26-37.
• 56. Dudzik K, Jurczak W: Influence of Friction Stir Welding on Corrosion Properties of Aw-7020M Alloy in Sea Water. Advances in Materials Science, 2015, 15(1), 7-13.
• 57. Zhou D, Xia Y, Gao Z, Bai L, Hu W: Effect of loading conditions on corrosion fatigue process of FSW AA6061-T6 joint in 3.5% NaCl studied by electrochemical noise. Journal of Materials Research and Technology, 2023, 24, 9808 9823.
• 58. Qiu Y, Yang X, Xu J, Li J, Xiang S, Chen Z, Sanders R E: Enhanced mechanical property and corrosion resistance of alloy 5182 FSW joints by Sc and Zr alloying. Materials Characterization, 2022, 194, 112412.
• 59. Raturi M, Bhattacharya A: Electrochemical corrosion of AA6061-AA7075 double sided FSW joints prepared with and without secondary heating. CIRP Journal of Manufacturing Science and Technology, 2022, 38, 590–612.
• 60. Rajendran C, Srinivasan K, Balasubramanian V, Balaji H, Selvaraj P: Feasibility study of FSW, LBW and TIG joining process to fabricate light combat aircraft structure. International Journal of Lightweight Materials and Manufacture, 2021, 4(4), 480–490.
• 61. Emmanuel Sam Franklin D, Vijay SJ, Mohanasundaram S, Nelson R, Hiran Gabriel D J: Investigations on GTAW and FSW of Al6061-ZrB2-Fly ash hybrid metal matrix composites. Materials Today: Proceedings, 2021, 47, 6902–6907.
• 62. Mehdi H, Mishra R S: Effect of friction stir processing on mechanical properties and heat transfer of TIG welded joint of AA6061 and AA7075. Defence Technology, 2021, 17(3), 715–727.
• 63. Kotari S, Punna E, Gangadhar Reddy S M, Venukumar S: Mechanical and micro structural behaviour of flux coated GTAW and FSW joined AA6061 aluminium alloy. Materials Today: Proceedings, 2020, 27, 1660–1667.
• 64. Mehdi H, Mishra RS: Investigation of mechanical properties and heat transfer of welded joint of AA6061 and AA7075 using TIG+FSP welding approach. Journal of Advanced Joining Processes, 2020, 1, 100003.
• 65. Walter V, Weidenmann K A, Schulze V: A Comparison of FSW, BHLW and TIG Joints for Al-Si-Mg Alloy (EN AW-6082 T6). Procedia CIRP, 2014, 18, 120–125.
• 66. Simoncini M, Ciccarelli D, Forcellese A, Pieralisi M: Micro- and Macro- Mechanical Properties of Pinless Friction Stir Welded Joints in AA5754 Aluminium Thin Sheets. Procedia CIRP, 2014, 18, 9–14.

Uwagi

Opracowanie rekordu ze środków MNiSW, umowa nr SONP/SP/546092/2022 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2024).