Hot Deformation Activation Energy of Metallic Materials Influenced by Strain Value

• Autorzy: Schindler I. , Opěla P. , Kawulok P. , Sauer M. , Rusz S. , Kuc D. , Rodak K.

Identyfikatory

DOI

10.24425/amm.2021.134779

• Języki publikacji: EN

Abstrakty

EN

Suitable and complete sets of stress-strain curves significantly affected by dynamic recrystallization were analyzed for 11 different iron, copper, magnesium, titanium or nickel based alloys. Using the same methodology, apparent hot deformation activation energy Q_p and Q_ss values were calculated for each alloy based on peak stress and steady-state stress values. Linear dependence between quantities Q_p and Q_ss was found, while Q_p values are on average only about 6% higher. This should not be essential in predicting true stress of a specific material depending on the temperature-compensated strain rate and strain.

Słowa kluczowe

EN

flow stress curves; steady state; metallic materials; hot deformation activation energy

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2021
• Tom: Vol. 66, iss. 1
• Strony: 223--228
• Opis fizyczny: Bibliogr. 42 poz., rys., tab., wzory

Twórcy

autor

Schindler I.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 2172/15, 708 00 Ostrava-Poruba, Czech Republic

autor

Opěla P.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 2172/15, 708 00 Ostrava-Poruba, Czech Republic

autor

Kawulok P.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 2172/15, 708 00 Ostrava-Poruba, Czech Republic

autor

Sauer M.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 2172/15, 708 00 Ostrava-Poruba, Czech Republic

autor

Rusz S.

• VSB - Technical University of Ostrava, Faculty of Materials Science and Technology, 17. Listopadu 2172/15, 708 00 Ostrava-Poruba, Czech Republic

autor

Kuc D.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 8 Krasińskiego Str., 40-019 Katowice, Poland

autor

Rodak K.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, 8 Krasińskiego Str., 40-019 Katowice, Poland

Bibliografia

• [1] C. Zener, J.H. Hollomon, J. Appl. Phys. 15 (1), 22-32 (1944), DOI: 10.1063/1.1707363.
• [2] M.A. Shafaat, H. Omidvar, B. Fallah, Mater. Des. 32 (10), 4689-4695 (2011), DOI: 10.1016/j.matdes.2011.06.048.
• [3] I. Schindler, R. Kawulok, H. Kulveitová, P. Kratochvíl, V. Šíma, M. Knapiński, Acta Phys. Pol. A. 122 (3), 610-613 (2012), DOI: 10.12693/APhysPolA.122.610.
• [4] C.M. Sellars, W.J. McG. Tegart, International Metallurgical Reviews. 17 (1), 1-24 (1972), DOI: 10.1179/IMTLR.1972.17.1.1.
• [5] H.J. McQueen, S. Yue, N.D. Ryan, E. Fry, J. Mater. Process.Technol. 53 (1-2), 293-310 (1995), DOI: 10.1016/0924-0136(95)01987-P.
• [6] I. Schindler, P. Kawulok, R. Kawulok, E. Hadasik, D. Kuc, High Temp. Mater. Processes. 32 (2), 149-155 (2013), DOI: 10.1515/htmp-2012-0106.
• [7] T. Li, G. Liu, M. Xu, B. Wang, T. Fu, Z. Wang, R.D.K. Misra, Materials 11, 2044 (2018), DOI: 10.3390/ma11102044.
• [8] R. Gujrati, C. Gupta, J.S. Jha, S. Mishra, A. Alankar, Mater. Sci. Eng. A 744,638-651 (2019), DOI: 10.1016/j.msea.2018.12.008.
• [9] X. Qian, N. Parson, X.G. Chen, Mater. Sci. Eng. A 764,138253 (2019), DOI: 10.1016/j.msea.2019.138253.
• [10] K.Ch. Nayak, P.P. Date, J. Mater. Eng. Perform. 28 (9), 5323-5343 (2019), DOI: 10.1007/s11665-019-04277-8.
• [11] P. Kawulok, I. Schindler, R. Kawulok, P. Opěla, R. Sedláček, Arch. Metall. Mater. 63 (4), 1785-1792 (2018), DOI: 10.24425/amm.2018.125105.
• [12] S. Zheng, X. Yuan, X. Gong, T. Le, A.V. Ravindra, Metall. Mater. Trans. A. 50 (5), 2342-2355 (2019), DOI: 10.1007/s11661-019-05162-8.
• [13] H. Gwon, S. Shin, J. Jeon, T. Song, S. Kim, B.C. De Cooman, Metals and Materials International. 25 (3), 594-605 (2019), DOI: 10.1007/s12540-018-00224-9.
• [14] V. Singh, Ch. Mondal, A. Kumar, P.P. Bhattacharjee, P. Ghosal, J. Alloys Compd. 788, 573-585 (2019), DOI: 10.1016/j.jallcom.2019.02.207.
• [15] B. Wang, Y. Zhang, B. Tian, V. Yakubov, J. An, A.A. Volinsky, Y. Liu, K. Song, L. Li, M. Fu, J. Alloys Compd. 781, 118-130 (2019), DOI: 10.1016/j.jallcom.2018.12.022.
• [16] I. Schindler, M. Sauer, P. Kawulok, K. Rodak, E. Hadasik, M.B. Jablonska, S. Rusz, V. Sevcak, Arch. Metall. Mater. 64 (2), 701-706 (2019).
• [17] W. Chen, W. Zeng, J. Xu, D. Zhou, S. Wang, S. He, J. Alloys Compd. 792, 389-398 (2019), DOI: 10.1016/j.jallcom.2019.03.345.
• [18] Q. Zhao, F. Yang, R. Torrens, L. Bolzoni, Mater. Des. 169, 107682 (2019), DOI: 10.1016/j.matdes.2019.107682.
• [19] I. Schindler, P. Kawulok, E. Hadasik, D. Kuc, J. Mater. Eng. Perform. 22 (3), 890-897 (2013), DOI: 10.1007/s11665-012-0327-8.
• [20] E. Hadasik, I. Schindler, D. Kuc, T. Mikuszewski, Arch. Metall. Mater. 62 (3), 1427-1432 (2017), DOI: 10.1515/amm-2017-0220.
• [21] N.D. Ryan, H.J. McQueen, J. Mater. Process. Technol. 21 (2), 177-199 (1990), DOI: 10.1016/0924-0136(90)90005-F.
• [22] E.I. Poliak, J.J. Jonas, Acta Mater. 44 (1), 127-136 (1996), DOI: 10.1016/1359-6454(95)00146-7.
• [23] M. Shaban, B. Eghbali, J. Mater. Sci. Technol. 27 (4), 359-363 (2011), DOI: 10.1016/S1005-0302(11)60074-1.
• [24] Y.C. Lin, M.S. Chen, J. Zhong, Computational Materials Science. 42 (3), 470-477 (2008), DOI: 10.1016/j.commatsci.2007.08.011.
• [25] S. Mandal, V. Rakesh, P.V. Sivaprasad, S. Venugopal, K.V. Kasiviswanathan, Mater. Sci. Eng. A. 500 (1/2), 114-121 (2009), DOI: 10.1016/j.msea.2008.09.019.
• [26] H.Y. Li, D.D. Wei, J.D. Hu, Y.H. Li, S.L. Chen, Computational Materials Science. 53 (1), 425-430 (2012), DOI: 10.1016/j.commatsci.2011.08.031.
• [27] L. Liu, Y.X. Wu, H. Gong, K. Wang, Trans. Nonferrous Met. Soc. China. 29 (3), 448-459 (2019), DOI: 10.1016/S1003-6326(19)64954-X.
• [28] S. Wang, J.R. Luo, L.G. Hou, J.S. Zhang, L.Z. Zhuang, Mater. Des. 113, 27-36 (2017), DOI: 10.1016/j.matdes.2016.10.018.
• [29] H. Mirzadeh, J.M. Cabrera, J.M. Prado, A. Najafizadeh, Mater. Sci. Eng., A. 528 (10/11), 3876-3882 (2011), DOI: 10.1016/j.msea.2011.01.098.
• [30] Ch. Li, Y. Liu, Y. Tan, F. Zhao, Metals. 8 (10), 846 (2018), DOI: 10.3390/met8100846.
• [31] A. Mohamadizadeh, A. Zarei-Hanzaki, H.R. Abedi, Mech. Mater. 95, 60-70 (2016), DOI: 10.1016/j.mechmat.2016.01.001.
• [32] D. Kuc, E. Hadasik, I. Schindler, P. Kawulok, R. Śliwa, Arch. Metall. Mater. 58 (1), 151-156 (2013), DOI: 10.2478/v10172-012-0166-5.
• [33] M. Rezaee, A. Zarei-Hanzaki, M. Ghambari, P.D. Nezhadfar, E. Ghasemi, Adv. Eng. Mater. 18 (6), 1075-1085 (2016), DOI: 10.1002/adem.201500426.
• [34] H. Mirzadeh, A. Najafizadeh, Mater. Sci. Eng. A. 527 (4/5), 1160-1164 (2010), DOI: 10.1016/j.msea.2009.09.060.
• [35] B.J. Yu, X.J. Guan, L.J. Wang, J. Zhao, Q.Q. Liu, Y. Cao, J. Cent. South Univ. Technol. 18 (1), 36-41 (2011), DOI: 10.1007/s11771-011-0655-0.
• [36] P. Changizian, A. Zarei-Hanzaki, A.A. Roostaei, Mater. Des. 39, 384-389 (2012), DOI: 10.1016/j.matdes.2012.02.049.
• [37] P. Opěla, PhD thesis, Popis deformačního odporu za tepla v širokémintervalu termomechanických podmínek [Hot Flow Stress De-scription in the wide range of thermomechanical conditions], VSB - Technical University of Ostrava, Czech Republic (2017).
• [38] P. Opěla, I. Schindler, P. Kawulok, F. Vančura, R. Kawulok, S. Rusz, T. Petrek, Metalurgija 54 (3), 469-472 (2015).
• [39] P. Opěla, I. Schindler, P. Kawulok, F. Vančura, R. Kawulok, S. Rusz, in: Metal 2016, Ostrava: Tanger Ltd, 458-463 (2016).
• [40] H. Mirzadeh, J. M. Cabrera, A. Najafizadeh, Acta Mater. 59 (16), 6441-6448 (2011), DOI: 10.1016/j.actamat.2011.07.008.
• [41] H. Mirzadeh, Mater. Chem. Phys. 152, 123-126 (2015), DOI: 10.1016/j.matchemphys.2014.12.023.
• [42] S. Saadatkia, H. Mirzadeh, J.M. Cabrera, Mater. Sci. Eng. A 636, 196-202 (2015), DOI: 10.1016/j.msea.2015.03.104

Uwagi

1. The paper was created thanks to the project No. CZ.02.1.01/0.0/0.0/17_049/0008399 (from the EU and CR financial funds provided by the Operational Programme Research, Development and Education, Call 02_17_049 Long-Term Intersectoral Cooperation for ITI), and the students grant projects SP2019/86 and SP2019/43 at VSB-TUO; managing authority: Czech Republic – Ministry of Education, Youth and Sports.

2. Opracowanie rekordu ze środków MNiSW, umowa Nr 461252 w ramach programu "Społeczna odpowiedzialność nauki" - moduł: Popularyzacja nauki i promocja sportu (2021).