Thermal Assessment of Modified Ultra-Light Magnesium-Lithium Alloys

• Autorzy: Król M. , Mikuszewski T. , Kuc D. , Tański T. , Hadasik E.

Identyfikatory

DOI

10.1515/amm-2017-0358

• Języki publikacji: EN

Abstrakty

EN

The paper presents the results of the influence of commercial TiBor and AlSr10 master alloys on the refine the grains size, hardness and crystallisation process based on the thermal-derivation analysis of light cast magnesium-lithium-aluminium alloys. The effects of TiBor and AlSr10 content on the characteristic parameters of the crystallisation process of Mg-Li-Al alloys were investigated by thermal-derivative analysis (TDA). Microstructural evaluations were identified by light microscope, X-ray diffraction, scanning electron microscopy, and energy dispersive X-ray spectroscopy. The results showed that the addition of TiBor master alloy reduced the grain size of Mg-9Li-1.5Al cast alloy from 900 μm to 500 μm, while the addition of AlSr10 master alloy reduced the grain size of investigated cast alloy from 900 μm to 480 μm. Moreover, an addition of TiBor and AlSr10 simultaneously reduced the grain size from 900 μm to 430 μm. Results from the thermal-derivative analysis showed that the addition of grain refinement causes a decrease in nucleation temperature and solidus temperature.

Słowa kluczowe

EN

cast magnesium-lithium alloys; crystallisation; thermal-derivative analysis; grain refinement

• Wydawca: Institute of Metallurgy and Materials Science of Polish Academy of Sciences ; Committee of Materials Engineering and Metallurgy of Polish Academy of Sciences
• Czasopismo: Archives of Metallurgy and Materials
• Rocznik: 2017
• Tom: Vol. 62, iss. 4
• Strony: 2433--2440
• Opis fizyczny: Bibliogr. 25 poz., rys., tab., wykr.

Twórcy

autor

Król M.

• Silesian University of Technology, Faculty of Mechanical Engineering, Institute of Engineering Materials and Biomaterials, 18A Konarskiego Str., 44-100 Gliwice, Poland

autor

Mikuszewski T.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, Institute of Metals Technology, 8 Krasińskiego Str., 40-019 Katowice, Poland

autor

Kuc D.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, Institute of Metals Technology, 8 Krasińskiego Str., 40-019 Katowice, Poland

autor

Tański T.

• Silesian University of Technology, Faculty of Mechanical Engineering, Institute of Engineering Materials and Biomaterials, 18A Konarskiego Str., 44-100 Gliwice, Poland

autor

Hadasik E.

• Silesian University of Technology, Faculty of Materials Engineering and Metallurgy, Institute of Metals Technology, 8 Krasińskiego Str., 40-019 Katowice, Poland

Bibliografia

• [1] A. Białobrzeski, J. Pezda, Archives of Foundry Engineering 12 (2), 143-146 (2012).
• [2] B. Jiang, Y. Zeng, M. Zhang, H. Yin, Q. Yang, F. Pan, T. Nonferr. Metal. Soc. 23, 904-908 (2013).
• [3] D. H. Stjohn, M. A. Easton, M. Qian, J. A. Taylor, Metall. Mater. Trans. A. 44A, 2935-2949 (2013).
• [4] A. Zieliński, G. Golański, M. Sroka, Mat. Sci. Eng. A-Struct. 682, 664-672 (2017), DOI: 10.1016/j.msea.2016.11.087.
• [5] L. A. Dobrzański, W. Borek, J. Mazurkiewicz, Materialwiss. Werkst. 47 (5-6) SI, 428-435 (2016).
• [6] L. A. Dobrzański, M. Czaja, W. Borek, K. Labisz, T. Tanski, Int. J. Mater. Prod. Tec. 51 (3), 264-280 (2015).
• [7] A. Zieliński, M. Miczka, B. Boryczko, M. Sroka, Arch. Civ. Mech. Eng. 4, 813-824 (2016), DOI:10.1016/j.acme.2016.04.010.
• [8] A. Zhang, H. Hao, X. Zhang, T. Nonferr. Metal. Soc. 23 (11), 3167-3172, (2013).
• [9] R. Wu, Y. Yan, G. Wang, L. E. Murr, W. Han, Z. Zhang, M. Zhang, Int. Mater. Rev. 60 (2), 65-100 (2015).
• [10] M. Sun, M. A. Easton, D. H. StJohn, G. Wu, T. B. Abbott, W. Ding, Adv. Eng. Mater. 15 (5), 373-378 (2013).
• [11] G. Wei, X. Peng, J. Liu, A. Hadadzadeh, Y. Yang, W. Xie1, Mater. Sci. Technol. 31 (14), 1757-1763 (2015).
• [12] T. Mikuszewski, Metalurgija 53, 588-590 (2014).
• [13] T. Mikuszewski, D. Kuc, Inżynieria Materiałowa 35 (3), 258-262 (2014).
• [14] I. Bednarczyk, D. Kuc, T. Mikuszewski, Hutnik 83 (8), 321-323 (2016).
• [15] R. Cheng, F. Pan, S. Jiang, Ch. Li, B. Jiang, X. Jiang, Prog. Nat. Sci. 23 (1), 7-12 (2013).
• [16] V. Kumar, Govind, K. Philippe, R. Shekhar, K. Balani, Procedia Materials Science 5, 585-591 (2014).
• [17] M. Krupinski, B. Krupinska, Z. Rdzawski, K. Labisz, T. Tanski, J. Therm. Anal. Calorim. 120 (3), 1573-1583 (2015).
• [18] M. Król, T. Tański, P. Snopiński, B. Tomiczek, J. Therm. Anal. Calorim. 127, 299-308 (2017), DOI 10.1007/s10973-016-5845-4.
• [19] R. Schmid-Fetzer, J. Gröbner, Metals 2 (3), 377-398 (2012).
• [20] N. C. Goel, J. R. Cahoon, Bulletin of Alloy Phase Diagrams 11 (6), 528-546 (1990), DOI:10.1007/BF02841712.
• [21] X. Guanglong, Z. Ligang, L. Libin, D. Yong, Z. Fan, X. Kai, L. Shuhong, T. Mingyue, J. Zhanpeng, Journal of Magnesium and Alloys 4, 249-264 (2016).
• [22] H. Baker, ASM Handbook, Alloy Phase Diagrams, 10th ed., ASM International 3, 1992.
• [23] A. Suzuki, N. D. Saddock, L. Riester, E. Lara-curzio, J. W. Jones, T. M. Pollock, Metall. Mater. Trans. A. 38 (2), 420-427 (2007).
• [24] B. Jiang, Y. Zeng, H. Yin, R. Li, F. Pan. Prog. Nat. Sci-Mater. 22 (2), 160-168 (2012).
• [25] J. Dutkiewicza, S. Rusz, W. Maziarz, W. Skuza, D. Kuc, O. Hilserb, Acta. Phys. Pol. A. 131 (5), 1303-1307 (2017).

Uwagi

EN

This publication was financed by the Ministry of Science and Higher Education of Poland as the statutory financial grant of the Faculty of Mechanical Engineering SUT.

PL

Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).