Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
2013 | 41 | Complete | 210-221
Tytuł artykułu

A critical assessment of lubrication techniques in machining processes: a case for minimum quantity lubrication using vegetable oil-based lubricant

Treść / Zawartość
Abstrakt, słowa kluczowe
Źródło
Twórcy
Bibliografia
Dodatkowe informacje
Warianty tytułu
Języki publikacji
EN
Abstrakty
EN
In this study, a review of the available literature on lubrication techniques during machining processes was conducted. Factors such as workpiece material, tool material and machining conditions were observed to be vital to the performance of any of the techniques. The performance and drawback of each technique were highlighted based on the machining conditions. It concludes by making a case for minimum quantity lubrication (MQL) method using vegetable oil-based lubricant in different machining processes, as a way of addressing the environmental health issues and cost associated with the application of lubricant in machining processes.
Słowa kluczowe
Czasopismo
Rocznik
Tom
41
Numer
Strony
210-221
Opis fizyczny
Twórcy
  • Department of Mechanical Engineering, School of Engineering & Engineering Technology, Federal University of Technology, P.M.B. 65, Minna, Nigeria , lawalbert2003@yahoo.com
  • Manufacturing System Integration, Department of Engineering Design and Manufacture, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur, Malaysia
  • Manufacturing System Integration, Department of Engineering Design and Manufacture, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur, Malaysia
  • Manufacturing System Integration, Department of Engineering Design and Manufacture, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur, Malaysia
Bibliografia
  • 1. Altan, E., Kıyak, M., Cakır, O., 2002. The effect of oxygen gas application in to cutting zone on machining. In: Proceedings of the Sixth Biennial Conference on Engineering Systems Design and Analysis (ESDA2002), Istanbul, pp. 1–5.
  • 2. Arnsek, A.& Vizintin, J., "Scuffing load capacity of rapeseed-based oils", J. Lubr. Eng., vol. 54, 8, 1999, p.11-18
  • 3. Arnsek, A.& Vizintin, J., "Lubricating properties of rapeseed-based oils", J. Synth. Lubr., vol. 16, 4, 2000, p.281-296
  • 4. Arnsek, A.& Vizintin, J., "Pitting resistance of rapeseed-based oils", J. Lubr. Eng., vol. 57, 3, 2001, p.17-21
  • 5. Asadauskas, S.& Perez, J.M.& Duda, J.L., "Oxidative stability and antiwear properties of high oleic vegetable oils", J. Lubr. Eng., vol. 52, 12, 1996, p.877-882
  • 6. Asadauskas, S.& Perez, J.M.& Duda, J.L., "Lubrication properties of castor oil – potential basestock for biodegradable lubricants", J. Lubr. Eng., vol. 53, 12, 1997, p.35-40
  • 7. ASM Handbook Committee, "Metals handbook", Properties and Selection Non-Ferrous Alloys and Pure Metals, vol. vol. 2, 1978
  • 8. Attanasio, A.& Gelfi, M.& Giardini, C.& Remino, C., "Minimal quantity lubrication in turning: effect on tool wear", Wear, vol. 260, 2006, p.333-338
  • 9. Autret, R., Liang, S.Y., 2003. Minimum Quantity Lubrication in Finish Hard Turning. HNICEM'03.
  • 10. Avuncan, G., "Machining Economy and Cutting Tools", 1998, pp. 375–403 (in Turkish)
  • 11. Baheti, U., Guo, C., Malkin, S., 1998. Environmentally conscious cooling and lubrication for grinding. In: Proceedings of the International Seminar on Improving Machine Tool Performance, vol. 2, pp. 643–654.
  • 12. Bennett, E.O.& Bennett, D.L., "Minimizing human exposure to chemicals in metalworking fluids", J. Am. Soc. Lubr. Eng., vol. 43, 3, 1987, p.167-175
  • 13. Bienkowski, K., "Coolants & lubricants—staying pure", Manuf. Eng., vol. March, 1993, p.55-61
  • 14. Boothroyd, Geoffrey& Knight, Winston A., "Fundamentals of Machining and Machine Tools", 2005, third ed.
  • 15. Braga, D.U.& Diniz, A.E.& Miranda, G.W.A.& Coppini, N.L., "Using a minimum quantity of lubricant (MQL) and a diamond coated tool in the drilling of aluminum–silicon alloys", J. Mater. Process. Technol., vol. 122, 1, 2002, p.127-138
  • 16. Brockhoff, T.& Walter, A., "Fluid minimization in cutting and grinding", Abrasives Mag., 1998, p.38-42
  • 17. Byrne, G.& Scholta, E., "Environmentally clean machining processes — a strategic approach", CIRP Ann. Manuf. Technol., vol. 42, 1, 1993, p.471-474
  • 18. Cakır, O.& Kıyak, M.& Altan, E., "Comparison of gases applications to wet and dry cuttings in turning", J. Mater. Process. Technol., vol. 153–154, 2004, p.35-41
  • 19. Cetin, M.H.& Ozcelik, B.& Kuram, E.& Demirbas, E., "Evaluation of vegetable based cutting fluids with extreme pressure and cutting parameters in turning of AISI 304L by Taguchi method", J. Clean. Prod., vol. 19, 2011, p.2049-2056
  • 20. Chen, D.C.& Suzuki, Y.& Sakai, K., "A study of turning operation by oil–water combined mist lubrication machining method", Key Eng. Mater., vol. 202–203, 2001, p.47-52
  • 21. Courbon, C.& Kramar, D.& Krajnik, P.& Pusavec, F.& Rech, J.& Kopac, J., "Investigation of machining performance in high-pressure jet assisted turning of Inconel 718: an experimental study", Int. J. Mach. Tools Manuf., vol. 49, 2009, p.1114-1125
  • 22. Davim, J.P.& Sreejith, P.S.& Gomes, R.& Peixoto, C., "Experimental studies on drilling of aluminum (AA1050) under dry, minimum quantity of lubricant, and flood-lubricated conditions", J. Eng. Manuf., vol. 220, 2006, p.1605-1611
  • 23. Davim, J.P.& Sreejith, P.S.& Silva, J., "Turning of brasses using minimum quantity of lubricant and flooded lubricant conditions", Mater. Manuf. Process., vol. 22, 2007, p.45-50
  • 24. German Social Accident Insurance (DGUV), Nov. 2010. Minimum Quantity Lubrication for Machining Operations. BGI/GUV-I718E (in German).
  • 25. Dhar, N.R.& Kamruzzaman, M., "Cutting temperature, tool wear, surface roughness and dimensional deviation in turning AISI-4037 steel under cryogenic condition", Int. J. Mach. Tools Manuf., vol. 47, 2007, p.754-759
  • 26. Dhar, N.R.& Paul, S.& Chattopadhyay, A.B., "Role of cryogenic cooling on cutting temperature in turning steel", Trans. ASME, vol. 124, 2002, p.146-154
  • 27. Dhar, N.R.& Kamuzzaman, M.& Ahmed, M., "Effect of minimum quantity lubrication (MQL) on tool wear and surface roughness in turning AISI-4340 steel", J. Mater. Process. Technol., vol. 172, 2006, p.299-304
  • 28. Diniz, Eduardo Anselom& Ricardo, Micaroni, "Influence of the direction and flow rate of the cutting fluid on tool life in turning process of AISI 1045 steel", Int. J. Mach. Tools Manuf., vol. 47, 2007, p.247-254
  • 29. Diniz, A.E.& Ferreira, J.R.& Filho, F.T., "Influence of refrigeration/lubrication condition on SAE 52100 hardened steel turning at several cutting speeds", Int. J. Mach. Tools Manuf., vol. 43, 3, 2003, p.317-326
  • 30. Eichenberger, H.F., 1991. Biodegradable Hydraulic Lubricant – an Overview of Current Developments in Central Europe. Paper No. 910062.
  • 31. El Baradie, M.A., "Cutting fluids, part I: characterization", J. Mater. Process. Technol., vol. 56, 1996, p.786-797
  • 32. Erdel, B.P., "Environmental issues in machining", SME Mach. Technol., vol. 10, 4, 1999
  • 33. Evans, C., "Cryogenic diamond turning of stainless steel", CIRP Ann. Manuf. Technol., vol. 40, 1, 1991, p.571-575
  • 34. Ezugwu, E.O., "Key improvements in the machining of difficult-to-cut aerospace super alloys", Int. J. Mach. Tools Manuf., vol. 4, 2005, p.1353-1367
  • 35. Ezugwu, E.O.& Bonney, J., "Effect of high-pressure coolant supply when machining nickel base Inconel-718 alloy with coated carbide tools", J. Mater. Process. Technol., vol. 153–154, 2004, p.1045-1050
  • 36. Ezugwu, E.O.& Bonney, J., "Finish machining of nickel base Inconel-718, alloy with coated carbide tool under conventional and high pressure coolant supplies", Tribol. Trans., vol. 48, 1, 2005, p.76-81
  • 37. Ezugwu, E.O.& Bonney, J.& Fadare, D.A.& Sales, W.F., "Machining of nickel base Inconel-718 alloy with ceramic tools under finishing conditions with various coolant supply pressure", J. Mater. Process. Technol., vol. 162–163, 2005, p.609-614
  • 38. Ezugwu, E.O.& Bonney, J.& Silva, R.B.D.& Akir, C.O., "Surface integrity of finished turned Ti–6Al–4V alloy with PCD tools using conventional and high pressure coolant supplies", Int. J. Mach. Tools Manuf., vol. 47, 2007, p.884-891
  • 39. Filipovic, A.& Stephenson, D.A., "Minimum quantity lubrication applications in automotive power-train machining", Machin. Sci. Technol., vol. 10, 2006, p.3-22
  • 40. Fox, N.J.& Stachowaik, G.W., "Vegetable oil-based lubricants – a review of oxidation", Tribol. Int., vol. 40, 2007, p.1035-1046
  • 41. Fratila, D., "Evaluation of near-dry machining effects on gear milling process efficiency", J. Clean. Prod., vol. 17, 2009, p.839-845
  • 42. Fratila, D.& Caizar, C., "Application of Taguchi method to selection of optimal lubrication and cutting conditions in face milling of AlMg3", J. Clean. Prod., vol. 9, 6–7, 2011, p.640-645
  • 43. Godlevski, V.A., "Water steam lubrication during machining", Tribology, vol. 162, 6, 1998, p.890-901, (in Italian)
  • 44. Greaves, I.A.& Eisen, E.A.& Smith, T.J.& Pothier, L.J.& Kriebel, D.& Woskie, S.R., "Respiratory health of automobile workers exposed to metalworking fluid aerosols: respiratory symptoms", Am. J. Ind. Med., vol. 32, 5, 1997, p.450-459
  • 45. Hafenbraedl, D.& Malkin, S., "Environmentally-conscious minimum quantity lubrication (MQL) for internal cylindrical grinding", Trans. NAMRI/SME, vol. 28, 2000, p.149-154
  • 46. Heinemann, R.& Hinduja, S.& Barrow, G.& Petuelli, G., "Effect of MQL on the tool life of small twist drills in deep-hole drilling", Int. J. Mach. Tools Manuf., vol. 46, 1, 2006, p.1-6
  • 47. Heisel, U.& Lutz, M.& Spath, D.& Wassmer, R.& Walter, U., "The Minimum Quantity of Fluid Technique and its Application to Metal Cutting, Machinery and Metals", 1998, pp. 22–38 (in Portuguese)
  • 48. Hohn, B.R.& Michaelis, K.& Dobereiner, R., "Load carrying capacity properties of fast biodegradable gear lubricants", J. Lubr. Eng., vol. 55, 11, 1999, p.15-38
  • 49. Howes, T.D.& Toenshoff, H.K.& Heuer, W., "Environmental aspects of grinding fluids", CIRP Ann. Manuf. Technol., vol. 40, 2, 1991, p.623-629
  • 50. Itoigawa, F.& Childs, T.H.C.& Nakamura, T.& Belluco, W., "Effects and mechanisms in minimal quantity lubrication machining of an aluminum alloy", Wear, vol. 260, 2006, p.339-344
  • 51. Jegatheesan, V.& Liow, J.L.& Shu, L.& Visvanathan, C., "The need for global coordination in sustainable development", J. Clean. Prod., vol. 17, 2009, p.637-643
  • 52. Jun, M.B.G.& Joshi, S.S.& DeVor, R.E.& Kapoor, S.G., "An experimental evaluation of an atomization-based cutting fluid application system for micromachining", J. Manuf. Sci. Eng. Trans. ASME, vol. 130, 3, 2008, p.0311181-0311188
  • 53. Kamata, Y.& Obikawa, T., "High speed MQL finish-turning of Inconel 718 with different coated tools", J. Mater. Process. Technol., vol. 192, 2007, p.281-286
  • 54. Kelly, J.F.& Cotterell, M.G., "Minimal lubrication machining of aluminum alloys", J. Mater. Process. Technol., vol. 120, 2002, p.327-334
  • 55. Kendall, A.L., "Friction and wear of cutting tools and cutting tool materials", ASM Handbook, vol. vol. 18, 1998, p.609-620
  • 56. Khan, A.A.& Mirghani, A.I., "Improving tool life using cryogenic cooling", J. Mater. Process. Technol., vol. 196, 1–3, 2008, p.149-154
  • 57. Khan, M.M.A.& Mithu, M.A.H.& Dhar, N.R., "Effects of minimum quantity lubrication on turning AISI 9310 alloy steel using vegetable oil-based cutting fluid", J. Mater. Process. Technol., vol. 209, 2009, p.5573-5583
  • 58. Klocke, F.& Eisenblaetter, G., "Dry cutting", CIRP Ann. Manuf. Technol., vol. 46, 2, 1997, p.519-526
  • 59. Kozma, M., "Investigation into the scuffing load capacity of environmentally friendly lubricating oils", J. Synth. Lubr., vol. 14, 3, 1997, p.249-258
  • 60. Krishna, P.V.& Rao, D. Nageswara, "Performance evaluation of solid lubricants in terms of machining", Int. J. Mach. Tools Manuf., vol. 48, 2008, p.1131-1137
  • 61. Krzan, B.& Vizintin, J., "Tribological properties of an environmentally adopted universal tractor transmission oil based on vegetable oil", Tribol. Int., vol. 36, 11, 2003, p.827-833
  • 62. Krzan, B.& Vizintin, J., "Vegetable-based oil as a gear lubricant", Gear Technol., vol. 20, 4, 2003, p.28-33
  • 63. Kumar, K.K.V.B.& Choudhury, S.K., "Investigation of tool wear and cutting force in cryogenic machining using design of experiments", J. Mater. Process. Technol., vol. 203, 1–3, 2008, p.95-101
  • 64. Lathkar, G.S.& Bas, U.S.K., "Clean metal cutting process using solid lubricants", Proceedings of the 19th AIMTDR Conference, 2000, p.15-31
  • 65. Lawal, S.A.& Choudhury, I.A.& Nukman, Y., "Application of vegetable oil-based metalworking fluids in machining ferrous metals – a review", Int. J. Mach. Tools Manuf., vol. 52, 2012, p.1-12
  • 66. Li, K.& Chou, S., "Experimental evaluation of minimum quantity lubrication in near micro-milling", J. Mater. Process. Technol., vol. 210, 2010, p.2163-2170
  • 67. Liao, Y.S.& Lin, H.M., "Mechanism of minimum quantity lubrication in high speed milling of hardened steel", Int. J. Mach. Tools Manuf., vol. 47, 2007, p.1660-1666
  • 68. Liu, Jie& Chou, Yevin K., "On temperatures and tool wear in machining hypereutectic Al–Si alloys with vortex-tube cooling", Int. J. Mach. Tools Manuf., vol. 47, 2007, p.635-645
  • 69. Lopez de Lacalle, L.N.& Perez-Bilbatua, J.& Sanchez, J.A.& Llorente, J.I.& Gutierrez, A.& Alboniga, J., "Using high pressure coolant in the drilling and turning of low machinability alloys", Int. J. Adv. Manuf. Technol., vol. 16, 2000, p.85-91
  • 70. Lopez de Lacalle, L.N.& Lamikiz, A.& Sanchez, J.A.& Cabanes, I., "Cutting conditions and tool optimization in the high-speed milling of aluminum alloys", Proc. Instn. Mech. Engrs. Part B, vol. 215, 2001, p.1257-1269
  • 71. Lopez de Lacalle, L.N.& Angulo, C.& Lamikiz, A.& Sanchez, J.A., "Experimental and numerical investigation of the effect of spray cutting fluids in high speed milling", J. Mater. Process. Technol., vol. 172, 1, 2006, p.11-15
  • 72. Machado, A.R.& Wallbank, J., "The effect of extremely low lubricant volumes in machining", Wear, vol. 210, 1–2, 1997, p.76-82
  • 73. MaClure, T.F.& Adams, R.& Gugger, M.D., "Comparison of Flood vs. Micro Lubrication on Machining Performance", 2001, Available at:, www.unist.com/pdfs/articles/AR_flood_v_micro.pdf, (accessed 30.01.09)
  • 74. Marksberry, P.W., "Micro-flood (MF) technology for sustainable manufacturing operations that are coolant less and occupationally friendly", J. Clean. Prod., vol. 15, 10, 2007, p.958-971
  • 75. Mazurkiewicz, M.,& Kubala, Z.& Chow, J., "Metal machining with high pressure water jet cooling assistance—a new possibility", J. Eng. Ind., vol. 111, 1989, p.7-12
  • 76. Mirghani, A.I.& Ismail, A.F.& Abakr, Y.A.& Nurul, A.A.K.M., "Effectiveness of cryogenic machining with modified tool holder", J. Mater. Process. Technol., vol. 185, 2007, p.91-96
  • 77. Miyoshi, K., 2007. Solid lubricants and coatings for extreme environments: state-of-the-art survey, NASA/TM-2007-214668.
  • 78. Mukhopadhyay, D.& Banerjee, S.& Reddy, N.S.K., "Investigation to study the applicability of solid lubricant in turning AISI 1040 steel", J. Manuf. Sci. Eng., vol. 129, 3, 2007, p.520-526
  • 79. Nakamura, T., Matsubara, T., Itoigawa, F., 2000. Development and study of oil film on water fog metalworking fluid application. In: Proc. of the Int. Tribol. Confer., Nagasaki, Japan, pp. 2269–2273.
  • 80. Nandy, A.K.& Gowrishankar, M.C.& Paul, S., "Some studies on high pressure cooling in turning of Ti–6Al–4V", Int. J. Mach. Tools Manuf., vol. 49, 2, 2009, p.182-192
  • 81. Odi-Owei, S., "Tribological properties of some vegetable oils and fats", J. Lubr. Eng., vol. 45, 11, 1988, p.685-690
  • 82. Ojmertz, K.M.C.& Oskarson, H.B., "Wear on SiC-whiskers reinforced ceramic inserts when cutting Inconel with water jet assistance", Tribol. Trans., vol. 43, 1999, p.471-478
  • 83. Palanisamy, Suresh& McDonald, Stuart D.& Dargusch, Matthew S., "Effects of coolant pressure on chip formation while turning Ti6Al4V alloy", Int. J. Mach. Tools Manuf., vol. 49, 2009, p.739-743
  • 84. Paul, S.& Dhar, N.R.& Chattopadhyay, A.B., "Beneficial effects of cryogenic cooling over dry and wet machining on tool wear and surface finish in turning AISI 1060 steel", J. Mater. Process. Technol., vol. 116, 2001, p.44-48
  • 85. Pusavec, F.& Krajnik, P.& Kopack, J., "Transitioning to sustainable production – part I: application on machining technologies", J. Clean. Prod., vol. 18, 2010, p.174-184
  • 86. Pusavec, F.& Krajnik, P.& Kopack, J., "Transitioning to sustainable production – part II: evaluation of sustainable machining technologies", J. Clean. Prod., vol. 18, 2010, p.1211-1221
  • 87. Quaile, Ron, "Understanding MQL", 2004, Available at:, www.mmsonline.com/articles/understanding-mql, (accessed 05.09.12)
  • 88. Rahim, E.A.& Sasahara, H., "A study of the effect of palm oil as MQL lubricant on high speed drilling of titanium alloys", Tribol. Int., vol. 44, 2011, p.309-317
  • 89. Rahman, M.& Senthil Kumar, A.& Manzoor-Ul-Salam, "Evaluation of minimal quantities of lubricant in end milling", Int. J. Adv. Manuf. Technol., vol. 18, 2001, p.235-324
  • 90. Rahman, M.& Kumar, A.S.& Salam, M.U., "Experimental evaluation on the effect of minimal quantities of lubricant in milling", Int. J. Mach. Tools Manuf., vol. 42, 5, 2002, p.539-547
  • 91. Rahmath Zareena, A.& Rahman, M.& Wong, Y.S., "Binderless CBN tools, a breakthrough for machining titanium alloys", J. Manuf. Sci. Eng., vol. 127, 2005, p.277-279
  • 92. Rao, D. Nageswara& Krishna, P. Vamsi, "The influence of solid lubricant particle size on machining parameters in turning", Int. J. Mach. Tools Manuf., vol. 48, 2008, p.107-111
  • 93. Sadeghi, M.H.& Haddad, M.J.& Tawakoli, T.& Emami, M., "Minimal quantity lubrication-MQL in grinding of Ti–6Al–4V titanium alloy", Int. J. Adv. Manuf. Technol., vol. 44, 2009, p.487-500
  • 94. Sales, W.F.& Diniz, A.E.& Machado, A.R., "Application of cutting fluids in machining processes", J. Braz. Soc. Mech. Sci., vol. 23, 2, 2001
  • 95. Sanchez, J.A.& Pombo, I.& Alberdi, R.& Izquierdo, B.& Ortega, N.& Plaza, S.& Martinez-Toledano, J., "Machining evaluation of a hybrid MQL-CO2 grinding technology", J. Clean. Prod., vol. 18, 2010, p.1840-1849
  • 96. Shaji, S.& Radhakrishnan, V., "Analysis of process parameters in surface grinding with graphite as lubricant based on the Taguchi method", J. Mater. Process. Technol., vol. 141, 2003, p.51-59
  • 97. Shane Hong, Y., "Economical and ecological cryogenic machining", J. Manuf. Sci. Eng., vol. 12, 2001, p.331-338
  • 98. Sharif, S.& Yusof, N.M.& Idris, M.H.& Ahmad, Z.B.& Sudin, I.& Ripin, A.& Mat Zin, M.A.H., "Feasibility Study of Using Vegetable Oil as a Cutting Lubricant through the Use of Minimum Quantity Lubrication during Machining", Research VOT No. 78055, 2009, eprints.utm.my/9729/1/78055.pdf, (accessed May 2011)
  • 99. Sharma, Vishal S.& Dogra, Manu& Suri, N.M., "Cooling techniques for improved productivity in turning", Int. J. Mach. Tools Manuf., vol. 49, 2009, p.435-453
  • 100. Shaw, M.C., "Energy conversion in cutting and grinding", CIRP Ann. Manuf. Technol., vol. 45, 1, 1996, p.101-104
  • 101. Shen, B., 2008. Minimum quantity lubrication grinding using nanofluids. PhD thesis, The University of Michigan, Michigan, USA.
  • 102. Silliman, J.D.& Perich, R., "Cutting and Grinding Fluids: Selection and Application", 1992, second ed., pp. 216
  • 103. Silva, L.R.& Bianchi, E.C.& Catai, R.E.& Fusse, R.Y.& Franca, T.V., "Study on the behavior of the minimum quantity lubricant – MQL technique under different lubricating and cooling conditions when grinding ABNT 4340 steel", J. Braz. Soc. Mech. Sci. Eng., vol. 27, 2, 2005, p.192-199
  • 104. Singh, Dilbagh& Rao, P.V., "Performance improvement of hard turning with solid lubricants", Int. J. Adv. Manuf. Technol., vol. 38, 2008, p.529-535
  • 105. Stäbler, D., Schönwald, M., Sefrin, H., Wolf, M., 2003. Hazard evaluation at the dry tooling of metallic materials. Final Project Report of the Süddeutsche Metal Professional Association, Germany (in German).
  • 106. Stephenson, D.A.& Barone, M.R.& Dargush, G.H., "Thermal expansion of the workpiece in turning", ASME J. Eng. Ind., vol. 117, 1995, p.542-550
  • 107. Su, Y.L.& Liu, T.H.& Su, C.T.& Yao, S.H.& Kao, W.H.& Cheng, K.W., "Wear of CrC-coated carbide tools in dry machining", J. Mater. Process. Technol., vol. 171, 2006, p.108-117
  • 108. Suzuki, S., "Developments in oil supplying systems for MQL cutting", J. Jpn. Soc. Tribol., vol. 47/7, 2002, p.538-543
  • 109. Tawakoli, T.& Hadad, M.J.& Sadeghi, M.H.& Daneshi, A.& Stöckert, S.& Rasifard, A., "An experimental investigation of the effects of workpiece and grinding parameters on minimum quantity lubrication – MQL grinding", Int. J. Mach. Tools Manuf., vol. 49, 2009, p.924-932
  • 110. Tawakoli, T.& Hadad, M.J.& Sadeghi, M.H., "Influence of oil mist parameters on minimum quantity lubrication – MQL grinding process", Int. J. Mach. Tools Manuf., vol. 50, 2010, p.521-531
  • 111. Tawakoli, T.& Hadad, M.J.& Sadeghi, M.H., "Investigation on minimum quantity lubricant-MQL grinding of 100Cr6 hardened steel using different abrasive and coolant – lubricant types", Int. J. Mach. Tools Manuf., vol. 50, 2010, p.698-708
  • 112. Tawakoli, T.& Hadad, M.& Sadeghi, M.H.& Daneshi, A.& Sadeghi, B., "Minimum quantity lubrication in grinding: effects of abrasive and coolant–lubricant types", J. Clean. Prod., vol. 19, 2011, p.2088-2099
  • 113. Taylor, F.W., "On the art of cutting metals", Trans. ASME, vol. 28, 1907, p.31-58
  • 114. Thamizhmanii, S.& Rosli& Hasan, S., "A study of minimum quantity lubrication on Inconel 718 steel", Arch. Mater. Sci. Eng., vol. 39, 1, 2009, p.38-44
  • 115. Trent, E.M., "Metal cutting and the tribology of seizure: the temperatures in metal cutting", Wear, vol. 128, 1988, p.65-81
  • 116. Trent, E.M.& Wright, P.K., "Metal Cutting", 2000, fourth ed.
  • 117. Tuholski, R.J., "Don't forget the cutting fluid", J. Indust. Technol., vol. Fall, 1993, p.2-5
  • 118. Varadarajan, A.S.& Philip, P.K.& Ramamoorthy, B., "Investigations on hard turning with minimal cutting fluid application (HTMF) and its comparison with dry and wet turning", Int. J. Mach. Tools Manuf., vol. 42, 2, 2002, p.193-200
  • 119. Vasu, S.& Reddy, G. Pradeep Kumar, "Effect of minimum quantity lubrication with Al2O3 nanoparticles on surface roughness, tool wear and temperature dissipation in machining Inconel 600 alloy", Proc. Instn. Mech. Engrs., Part. N. J. Nanoeng. Nanosyst., vol. 225, 1, 2011, p.3-16
  • 120. Venugopal, K.A.& Paul, S.& Chattopadhyay, A.B., "Growth of tool wear in turning of Ti–6Al–4V alloy under cryogenic cooling", Wear, vol. 262, 2007, p.1071-1078
  • 121. Vikram, C.H.& Kumar, R.& Ramamoorthy, B., "Performance of coated tools during hard turning under minimum fluid application", J. Mater. Process. Technol., vol. 185, 2007, p.210-216
  • 122. Vizintin, J.& Arnsek, A.& Ploj, T., "Lubricating properties of rapeseed oils compare to mineral oils under a high load oscillating movement", J. Synth. Lubr., vol. 17, 3, 2000, p.201-217
  • 123. Wakabayashi, T.& Sato, H.& Inasaki, I., "Turning using extremely small amounts of cutting fluids", JSME Int. J., vol. 41, 1998, p.143-148
  • 124. Wang, Z.Y.& Rajurkar, K.P., "Cryogenic machining of hard-to-cut materials", Wear, vol. 239, 2000, p.168-175
  • 125. Weingaernter, W.& Schroeter, R.& Teixeira, C.R., "“Effects of Cutting Fluids Minimization” Machinery and Metals", 2000, pp. 52–59 (in Portuguese)
  • 126. Wertheim, R.& Ber, A.& Rotberg, J., "Influence of high pressure flushing through the rake face of the cutting tool", CIRP Ann. Manuf. Technol., vol. 41, 1, 1992, p.101-106
  • 127. Yerkes, K.L., Dorian, J., 1999. Micro-cooler for chip-level temperature control. In: Aero System Power Conference, Arizona, 1401–1404, pp. 1–9.
  • 128. Yildiz, Y.& Nalbant, M., "A review of cryogenic cooling in machining processes", Int. J. Mach. Tools Manuf., vol. 48, 2008, p.947-964
  • 129. Yoshimura, H., Niwa, N., Nakamura, T., Itoigawa, F., 2003. Study on ecofriendly oil on water drop cutting fluid. In: Proceeding of the Int. Confer. on LEM, vol. 21, pp. 1065–1070.
  • 130. Zhang, S.& Li, J.F.& Wang, Y.W., "Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting condition", J. Clean. Prod., vol. 32, 2012, p.81-87
Kolekcja
Elsevier
Identyfikator YADDA
bwmeta1.element.elsevier-37b98462-a934-3a24-9cbe-73ffe0f3f0ea
Identyfikatory
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.