The initial analysis of the aerodynamic characteristics of a 3D printed model of an aircraft
Treść / Zawartość
The aerodynamic research into models of an aircraft aims at creating the main characteristics of aerodynamic forces and moments and the aerodynamic characteristics of coefficients of aerodynamic forces and moments, based on real dimensions. The method of 3D printing was used to create a model of an aircraft. The model with the previously set printing parameters and commands for a 3D printer, in the right order, was imported into MakerBot Print. The final stage was printing the model. The printed components of the model of an aircraft were imperfect due to the incorrectly set printing parameters. The model with the previously set printing parameters and commands for a 3D printer, in the right order, was imported into MakerBot Print. The final stage was printing the model. The printed components of the model of an aircraft were imperfect due to the incorrectly set printing parameters. The printing parameters were corrected in the next printing sessions so the surfaces of the components were good enough and grinding was unnecessary. Some excess material was removed in each of the printed components, and the slots were cleaned. Then, the individual models were put together. The article describes the technique of creating a model of an aircraft to map its exact geometry for experimental wind tunnel research. 3D printing enables us to experimentally investigate a created geometry, in particular to investigate further prior to releasing an aircraft to service. The 3D model employs the model created in line with the previous CFD analysis.
Bibliogr. 10 poz., rys.
- Lublin University of Technology Faculty of Mechanical Engineering, Department of Thermodynamics Fluid Mechanics and Aviation Propulsion Systems Nadbystrzycka Street 36, 20-618 Lublin, Poland tel.:+48 81 538 42 84, fax: +48 81 538 47 49, firstname.lastname@example.org
- Polish Air Force Academy Aeronautics Faculty, Department of Airframe and Engine Dywizjonu 303 Street 35, 08-521 Deblin, Poland tel.:+48 261 517 430, fax: +48 261 517 417x, email@example.com
-  Czyż, Z., Łusiak, T., Magryta, P., CFD Numerical Testing for the Effect of Fault on the Aerodynamic Characteristics of Windmillers, Transactions of the Institute of Aviation, 232 pp. 3-14, 2013.
-  Łusiak, T., Czyż, Z., Kłoda, Ł., Chabros, M., Dżaman, E., Comparative analysis of the results of numerical tests of wind turbines with the results of tests in wind tunnels, 2013.
-  Łusiak, T., Wendeker, M., Aerodynamic research of the Fusincopter hull, Lublin University of Technology, Department of Thermodynamics, Fluid and Aviation Propulsion Systems, 2/92/NN/2013, Lublin 2013.
-  Ruchała, P., Stryczniewicz, W., Czyż, Z., Łusiak, T., Aerodynamic characteristics of windmill hull for different angles of horizontal impact wedging, Transactions of the Institute of Aviation, No. 4 (241), pp. 96-107, Warszawa 2015.
-  Compa, T., Aircraft Knowledge Base, WSOSP, Deblin 2012.
-  Wiśniowski, W., Aerodynamic tunnels in Poland in comparison with world tunnels, Scientific Publishing House of the Institute of Aviation, Warszawa 2016.
-  Barlow, J., Rae, W. H., Pope, A., Low-speed wind tunnel testing.
-  https://content.sciendo.com, 06.04.2018.
-  Smykla, I., Selected aerodynamic and flight mechanics issues (flight rules), Warszawa 2008.
-  Sobieraj, W., Aerodynamic, Wojskowa Akademia Techniczna, Warszawa 2014.
Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).