Ograniczanie wyników
Czasopisma help
Autorzy help
Lata help
Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników

Znaleziono wyników: 385

Liczba wyników na stronie
first rewind previous Strona / 20 next fast forward last
Wyniki wyszukiwania
Wyszukiwano:
w słowach kluczowych:  analiza termiczna
help Sortuj według:

help Ogranicz wyniki do:
first rewind previous Strona / 20 next fast forward last
EN
Kaolinite was subjected to microwave (MW) and chemical modification with silane and copper acetate. The process was carried out for 30, 60 and 120 min. The use of microwave radiation shortened the time of kaolinite modification (from several days to 30 min). The presence of modifying compounds in the kaolinite structure was confirmed by FT-IR, DSC, TGA and SEM. The use of modified kaolinite (10 phr) reduced the rate of vulcanization of natural rubber and facilitated its processing. Moreover, silane-modified kaolinite increased the tensile strength and hardness of natural rubber, which indicates its strengthening effect.
PL
Kaolinit poddano działaniu mikrofal (MW) oraz modyfikacji chemicznej silanem i octanem miedzi. Proces prowadzono przez 30, 60 i 120 min. Zastosowanie promieniowania mikrofalowego skróciło czas modyfikacji kaolinitu (z kilku dni do 30 min). Obecność związków modyfikujących w strukturze kaolinitu potwierdzono metodą FT-IR, DSC, TGA i SEM. Zastosowanie modyfikowanego kaolinitu (10 phr) zmniejszyło szybkość wulkanizacji naturalnego kauczuku i ułatwiło jego przetwórstwo. Ponadto kaolinit modyfikowany silanem zwiększył wytrzymałość na rozciąganie i twardość kauczuku naturalnego co świadczy o jego wzmacniającym działaniu.
EN
Composites consisting of polyurea (PUA) as a matrix material, reinforced with the addition of copper oxide nanoparticles (CuONPs) used in various mass ratios (0.5%, 1%, 2%, 3%, 4%, 5%, 6%, 7%, 8%, 9% and 10%) were tested. The resulting composites were examined for their mechanical (hardness, tensile strength, compressive strength), thermal (thermal conductivity, thermogravimetric analysis) and structural (FTIR) properties. The tests showed that reinforcing polyurea with copper oxide nanoparticles improved the mechanical properties (hardness and elastic modulus), while compressive strength decreased by 77% at a weight percentage of 6%, and the best result was obtained at a weight percentage of 1%. Heat treatment also affected the mechanical properties; for example, hardness increased at 7°C and 80°C. Thermal conductivity increased by 57% with the addition of the reinforcement material at room temperature and further increased during heat treatment at 7°C and 80°C. Thermal analysis showed slight changes in the curves, resulting in an improvement in the resistance of the matrix to thermal decomposition. The infrared spectrum showed that the nanoparticles bands overlapped with the matrix. Scanning electron microscopy (SEM) characterization revealed the presence of bonding between the copper nanoparticles (CuONPs) and the polyurea (PUA) matrix.
PL
Przeprowadzono badania kompozytów składających się z polimocznika (PUA) jako materiału matrycowego, wzmocnionego dodatkiem nanocząstek tlenku miedzi (CuONPs) stosowanego w różnych proporcjach masowych (0,5%, 1%, 2%, 3%, 4%, 5%, 6%, 7%, 8%, 9% i 10%). Otrzymane kompozyty badano pod kątem ich właściwości mechanicznych (twardość, wytrzymałość na rozciąganie, wytrzymałość na ściskanie), termicznych (przewodność cieplna, analiza termograwimetryczna) i strukturalnych (FTIR). Badania wykazały, że wzmocnienie polimocznika nanocząsteczkami tlenku miedzi poprawiło właściwości mechaniczne (twardość i moduł sprężystości), natomiast wytrzymałość na ściskanie spadła o 77% przy udziale masowym tlenku miedzi 6%, a najlepszy wynik uzyskano dla kompozytów zawierających 1% tlenku miedzi. Obróbka cieplna również wpłynęła na właściwości mechaniczne, twardość wzrosła w temp. 7°C i 80°C. Przewodność cieplna wzrosła o 57% po dodaniu materiału wzmacniającego w temperaturze pokojowej i dalej wzrosła podczas obróbki cieplnej w temp. 7°C i 80°C. Analiza termiczna wykazała niewielkie zmiany krzywych, wynikające z poprawy odporności matrycy na rozkład termiczny. Widmo kompozytu w podczerwieni wykazało, obecność dodatkowego pasma wskazującego na obecność nanomateriału Cu-O i podwójnego pasma pochodzącego od grupy C=O co wskazuje na interakcję między nanocząstkami CuO a grupą C=O matrycy. Charakterystyka metodą elektronowej mikroskopii skaningowej (SEM) ujawniła obecność wiązania między nanocząsteczkami miedzi (CuONP) a matrycą polimocznikową (PUA).
EN
The paper presents the questions of thermal analysis of concrete structures in fire situation. There are described general rules as well as practical methods for conductiong thermal analysis. The basic recommendations and detailed informations included within this scope in the new code for fire design are also discussed, with special attention paid to the differences in comparison with the present code PN-EN 1992-1-2.
PL
W artykule przedstawiono zagadnienie analizy termicznej konstrukcji z betonu w warunkach oddziaływania pożarowego. Podano ogólne zasady prowadzenia takiej analizy, a także opisano możliwe praktyczne sposoby jej realizacji. Skomentowano zalecenia i szczegółowe informacje zawarte w nowej normie do projektowania konstrukcji z betonu na warunki pożarowe, przedstawiając różnice w porównaniu z obecną normą PN-EN 1992-1-2.
EN
Experimental studies were conducted in laboratory conditions to assess the suitability of alder and birch for use in individual home furnaces and the potential storage of ashes in the environment. Raw biomass samples were combusted at 450-500 ± 15°C. The tree species (alder and birch) originated from Poland (Małopolskie Voivodeship) and the “Bory Tucholskie” National Park (Pomorskie Voivodeship). This study aimed to determine the content of toxic metals (As, Cd, Cr, Cu, Hg, Ni, Pb, Tl) in raw biomass and its ashes, ions eluted from water eluates of ash, and to analyze the thermal degradation process of wood. In addition to the analysis, the study used inductively coupled plasma optical emission spectroscopy (ICP-OES) and ion chromatography (IC), thermogravimetric analysis analyses (TG/DSC), and powder X-ray diffraction. The content of volatile parts in wood biomass ranges between 67.2-82.5%, ash content 2.9-19.1%, and calorific value 14.8-17.1 MJ/kg. Moisture content in the wood biomass ranges from 14.6-18.7% (birch) and 17-19.2% (alder). The content of toxic metals was generally low in raw biomass, except for Co, Zn, and Ni, and higher in ashes, varying depending on the origin of the biomass. TG/DSC curves allowed for the identification of the main stages of wood biomass degradation, corresponding to moisture content in the range of 2.73-5.83% (wt.%), ash (0.58-3.68% wt.%), volatile matter (59.63-76.46% wt.%), and fixed carbon (20.23-32.3% wt.%). Higher sulfate and potassium ion concentrations were detected in water eluates of ashes from the “Bory Tucholskie” National Park. The research results do not indicate that alder and birch may be used for low-temperature combustion. However, it is advisable to conduct comprehensive studies research in this area.
PL
Przeprowadzono badania eksperymentalne w warunkach laboratoryjnych w celu oceny przydatności olchy i brzozy do wykorzystania w indywidualnych piecach domowych oraz potencjalnego wykorzystania i składowania popiołów w środowisku. Próbki biomasy surowej spalano w temperaturze 450-500 ± 15°C. Gatunki drzew pochodzą z Polski (województwo małopolskie) oraz z Parku Narodowego „Bory Tucholskie” (województwo pomorskie). Celem niniejszego badania było określenie zawartości metali toksycznych (As, Cd, Cr, Cu, Hg, Ni, Pb, Tl) w biomasie surowej i jej popiołach, wymywanych jonów z eluatów wodnych popiołów i analiza procesu termicznej degradacji drewna. W badaniach wykorzystano metodę spektroskopii emisyjnej ze wzbudzeniem w plazmie indukcyjnie sprzężonej (ICP-OES) i chromatografię jonową (IC), wykonano analizy termograwimetryczne (TG/DSC) oraz dyfrakcję rentgenowską metodą proszkową (XRD). Zawartość części lotnych w biomasie drzewnej waha się między 67,2-82,5%, zawartość popiołu 2,9-19,1%, a wartość kaloryczna wynosi 14,8-17,1 MJ/kg. Zawartość wilgoci w biomasie drzewnej waha się między 14,6-18,7% (brzoza) i 17-19,2% (olcha). Skład mineralny badanych próbek jest mało zróżnicowany. Zawartość metali toksycznych jest na ogół niska w biomasie surowej, z wyjątkiem miedzi, cynku i niklu, oraz wyższa w popiołach, zróżnicowana w zależności od pochodzenia biomasy. Krzywe TG/DSC pozwoliły zidentyfikować główne etapy degradacji biomasy drzewnej, które odpowiadają zawartości wilgoci w zakresie 2,73-5,83% (wag.), popiołu 0,58-3,68% (wag.), materiałów lotnych 59,63-76,46% (wag.) oraz węgla stałego 20,23-32,3% (wag.). Wyższe stężenia jonów siarczanowych i potasowych oznaczono w eluatach wodnych popiołów z Parku Narodowego „Bory Tucholskie”. Wyniki badań niejednoznacznie wskazują, że olcha i brzoza mogą być wykorzystane w spalaniu niskotemperaturowym; jednak wskazane jest prowadzenie kompleksowych badań w tym zakresie.
EN
The elaboration contains the history of the development of coordination chemistry at the Maria Curie-Skłodowska University in Lublin. The Department of General and Coordination Chemistry and Crystallography at the Institute of Chemical Sciences, Faculty of Chemistry, Maria Curie-Skodowska University conducts research on metal complexes. Coordination chemistry in Lublin is inextricably associated with Professor Wanda Brzyska, who in the mid-1950s began her scientific career at the Department of Inorganic Chemistry headed by Professor Włodzimierz Hubicki. Professor Brzyska moved away from teamics related to the separation processes of rare earth elements, focusing mainly on the synthesis and characterization of coordination compounds in the solid phase, based on rare earth elements and carboxylic acids. The study presents the development of research topics over the years in the area of coordination chemistry, the evolution of methods, and the research equipment used.
PL
Techniki termoanalityczne, m.in. skaningowa kalorymetria różnicowa i termograwimetria, pozwalają na badanie właściwości materiałów, używając ich niewielkich ilości. Umożliwiają uzyskiwanie wielu rzetelnych informacji o próbkach materiałów wybuchowych w stosunkowo krótkim czasie przy zachowaniu bezpieczeństwa operatora i otoczenia. Przebieg pomiarów oraz ich rezultaty zależą od wielu czynników, a potencjalne błędy mogą powstawać na różnych etapach, od momentu pobierania próbek do badań do momentu wyciągania wniosków. Odpowiedni dobór parametrów badania oraz właściwa analiza i interpretacja wyników, stanowią szczególne wyzwanie dla prowadzącego badania.
EN
Thermoanalytical techniques, including differential scanning calorimetry and thermogravimetry, allow to test the properties of materials using small amounts. They enable obtaining a lot of reliable information about samples of explosives in a relatively short time, while maintaining operator and surroundings safety. The course of measurements and their results depend on many factors, and potential errors can arise at various stages, from taking samples for tests until conclusions are drawn. Appropriate selection of test parameters as well as proper analysis and interpretation of results pose a special challenge for the researcher.
PL
W artykule przedstawiono metodę oznaczania wartości opałowej koksów z zastosowaniem różnicowej kalorymetrii skaningowej (DSC) połączonej z analizą termograwimetryczną (TGA). Opracowana technika jest alternatywą dla obecnie stosowanych metod. W odróżnieniu od nich, oznaczanie wartości opałowej za pomocą TGA/DSC umożliwia charakteryzowanie miligramowych prób koksów, o różnym stopniu odgazowania, uzyskanych z różnorodnych paliw. Zastosowanie opisywanej metody, pozwala dodatkowo na wyznaczenie zmiany wartości opałowej analizowanych prób, w zależności od stopnia konwersji paliwa oraz pośrednie oznaczenie wartości opałowej części lotnych. Weryfikacji wyników uzyskanych za pomocą techniki TGA/DSC dokonano na podstawie metody znormalizowanej, przy zastosowaniu bomby kalorymetrycznej. Rozbieżności pomiędzy wartościami zmierzonymi dla koksów z biomasy i węgla kamiennego, koksu ponaftowego oraz grafitu wyniosły od 0,2 MJ/kg do 0,8 MJ/kg.
EN
The study presents a method for determining the calorific value of cokes using differential scanning calorimetry (DSC) combined with thermogravimetric analysis (TGA). The developed technique serves as an alternative to currently used methods. Unlike traditional approaches, determining the calorific value using TGA/DSC allows for the characterization of milligram-sized coke samples with varying degrees of devolatilization, obtained from diverse fuels. Additionally, the described method enables the determination of calorific value change profiles of the analyzed samples depending on the degree of fuel conversion, as well as the indirect determination of the calorific value of volatile matter. The results obtained using the TGA/DSC technique were validated against a standardized method employing a bomb calorimeter. Discrepancies between the measured values for biomass and bituminous coal cokes, petroleum coke, and graphite ranged from 0.2 MJ/kg to 0.8 MJ/kg.
EN
Mineral admixtures and waste by-products in concrete exhibit economical and environmental benefits, but their cementing and engineering properties should be assessed before practical adoption. In this study, we investigated hydration and physical properties of Self-Consolidating (SCM) and Ordinary (OM) mortars, based on slag-blended Portland limestone cement (PLC), with equivalent water-to-cement ratio (E/C≈ 0.55). The variables were mortar type and mineral admixture type, limestone powder (LP) or silica fume (SF). Therefore, we made two ordinary mortars (OMs), Oref (OPC based) and Oplc (slag PLC based), and two self-consolidating mortars (SCMs), SplcL (limestone based) and SplcS (silica fume based). We assessed compressive strength, sorptivity, hydration heat, thermogravimetric analysis, and SEM images. Results reveal that Oplc exhibits similar to better performance than Oref; blended LP leads to 36% higher mechanical strength, more than 50% carboaluminate in SCMs, and 40% lower heat and rate of hydration, and seems to have packing role and doesn't contribute to more sites’ nucleation; SF is efficient when substituted more than 10%.
11
Content available remote Eliminacja węgla z koncentratu miedzi w piecu fluidalnym
PL
Technologia prażenia koncentratów jest ściśle związana z produkcją miedzi i jest prowadzona w piecu ze złożem fluidalnym. Materiał wsadowy do pieca jest jednocześnie metalonośny i energetyczny ze względu na zawarte w nim związki węgla organicznego oraz siarczki. Prażenie koncentratów ma na celu eliminację węgla organicznego oraz konwersję siarki z formy siarczkowej na siarczanową. W pracy przedstawiono wyniki badań przeprowadzanych z wykorzystaniem analizy termicznej metodami TG, DTG i DSC, dokonano identyfikacji zakresu występowania zachodzących przemian i zmian masy podczas procesu prażenia wraz ze składem fazowym produktu. Stwierdzono, że możliwe jest skuteczne usuwanie węgla w procesie przemysłowym w zakresie temp. 650-750°C z jednoczesnym prażeniem siarczanującym.
EN
The Cu-bearing concentrates were analyzed for TG, DGT, and DSC thermal anal. Mass changes, both phase and chem. transitions and temp. ranges in which they occurred were identified. It was possible to successfully remove C from Cu concentrates during industrial process run in temp. range 650-750 ̊C and also simultaneously performed sulfating roasting.
PL
W pracy przedstawiono wyniki numerycznej trójwymiarowej analizy termicznej w stanie ustalonym macierzy laserów VCSEL (laserów emitujących z powierzchni z pionową wnęką rezonansową) emitujących falę 850 nm, wykorzystując metodę elementów skończonych. Zbadano wpływ na wzrost temperatury w matrycy rozmiaru apertury tlenkowej obszaru czynnego pojedynczych emiterów matrycy, rozmiaru matrycy, rozmiaru podłoża, odległości między emiterami, ilości ciepła wydzielonego w każdym emiterze oraz jakości połączenia termicznego między matrycą a chłodnicą.
EN
A thermal 3D steady-state analysis of 850 nm vertical cavity surface emitting laser (VCSEL) arrays based on the finite element method (FEM) is presented in this paper. Several oxide aperture diameters active region of single emitter, array sizes and substrate sizes, several values of the distance between adjacent emitters, various heat source densities, and the impact of the quality of thermal connections between the semiconductor structure and the heat sink are considered.
PL
W artykule przedstawiono podstawowe informacje o wybranych inicjujących materiałach wybuchowych, powszechnie stosowanych w środkach bojowych. Szczególną uwagę skupiono na właściwościach termicznych takich związków jak piorunian rtęci, tetrazen, azydek ołowiu, trójnitrorezorcynian ołowiu (TNRPb). Znajomość właściwości termicznych ww. inicjujących materiałów wybuchowych, pozwala na ich bezpieczne zastosowanie. Właściwości termiczne zostały zbadane z zastosowaniem technik DSC (różnicowa kalorymetria skaningowa) i TGA (analiza termograwimetryczna). Otrzymane wyniki potwierdzają, iż analiza termiczna (DSC i TGA) jest szybką i bezpieczną metodą pozwalającą badać właściwości termiczne inicjujących materiałów wybuchowych, jak i pozostałych materiałów wysokoenergetycznych.
EN
The article presents basic information about selected primary explosives commonly used in warfare agents. Special attention was focused on the thermal properties of such compounds as mercury fulminate, tetrazene, lead azide, lead trinitroresorcinate. Knowledge of the thermal properties of the above-mentioned primary explosives, allows their safe use. Thermal properties have been studied by using DSC (differential scanning calorimetry) and TGA (thermogravimetric analysis) techniques. The results obtained confirm that thermal analysis (DSC and TGA) is a fast and safe method to study the thermal properties of primary explosives as well as other high-energy materials.
14
Content available remote Zasady opracowywania katalogu złączy budowlanych (mostków cieplnych)
PL
W artykule przedstawiono zasady opracowywania kart katalogowych złączy budowlanych (mostków cieplnych) oraz przykładowe ich zastosowania.
EN
The article presents the principles of developing catalogue cards for construction joints (thermal bridges) and examples of their applications.
EN
This article presents the issue of recycling and maintaining the processing properties of materials made of plastics. For this purpose, samples from recycled, low-density, polyethylene were tested. The impact of the use of dyes and surface printing on the lifecycles of material and its quality was examined. For this purpose, an analysis was carried out using differential scanning calorimetry and thermos-gravimetry. It was found that the use of dyes may affect the quality of the material and increase the disposal costs of pre-used materials.
EN
Proper design of power installations with the participation of power cables buried in homogeneous and thermally well-conductive ground does not constitute a major problem. The situation changes when the ground is non-homogeneous and thermally low-conductive. In such a situation, a thermal backfill near the cables is commonly used. The optimization of thermal backfill parameters to achieve the highest possible current-carrying capacity is insufficiently described in the standards. Therefore, numerical calculations based on computational fluid dynamics could prove helpful for designers of power cable lines. This paper studies the influence of dimensions and thermal resistivity of the thermal backfill and thermal resistivity of the native soil on the current-carrying capacity of power cables buried in the ground. Numerical calculations were performed with ANSYS Fluent. As a result of the research, proposals were made on how to determine the current-carrying capacity depending on the dimensions and thermal properties of the backfill. A proprietary mathematical function is presented which makes it possible to calculate the cable current-carrying capacity correction factor when the backfill is used. The research is expected to fill the gap in the current state of knowledge included in the provisions of standards.
EN
Purpose: The brake system is the most significant component of a vehicle because it protects the driver, passengers, other road users, and property on both sides of the road. The basic principle of the disc brake system depends on the friction-based between the brake pads and rotor disc. Design/methodology/approach: The paper introduced a developed 3D finite element thermal model of the brake system to simulate the heat generated by friction in the vehicle's disc brake. Findings: The results presented the surface temperature at any instant of the disc brake under various initial velocities when the materials properties of the rotor disc and pad depend on temperature. Research limitations/implications: The main aim of the present paper is to build a numerical model to simulate the braking process under various initial vehicle velocities and investigate the influence of the material properties when they function on temperature and constant. Originality/value: The maximum difference between the two cases (contact and depend on the temperature) was 17 K for the initial velocity of 144,120. Also, it was found out that the percentage differences of the surface temperature increasing with the rise in initial vehicle velocity were 323% and 392.5% when the initial velocity of the vehicle increased from 100 km/h to 144 km/h.
EN
The article presents the influence of the percentage share of pig iron and steel scrap on the chemical composition, physicochemical and mechanical properties. Using an induction furnace, 6 melts were carried out with a variable amount of pig iron in the charge from 0 to 50%. For carburizing, a RANCO 9905 carburizer with a carbon content of 99.2% was used. After melting and introducing FeSi75, temperature measurement was carried out and the metal was superheated to 1500°C. The next step was to pour the samples for chemical analysis, DTA (Derivation Thermal Analysis) and strength and hardness from the melting furnace without inoculation. The last step was to carry out the inoculation by introducing 0.3% barium inoculant into the vat and pouring samplers for DTA analysis. The inoculation was carried out solely to determine changes in DTA parameters, mainly Temin, compared to castings without inoculation.
EN
Plastics are widely used in various industries and households, which has an impact on the condition of the natural environment in terms of waste. Today, the leading plastics’ disposal method is landfilling. It should be emphasized that the production of electricity in Poland is based mainly on hard coal and lignite, which is associated with the continuous production of various types of waste, including post-flotation coal waste (coal sludge). That is why rational waste management, recycling, proper disposal, use, and improvement of the existing and implementation of new technological solutions are crucial for environmental protection. This study undertakes cognitive research on the possibility of using PA6 polyamide waste, marked by high calorific value. Thermal analysis techniques (DSC-TG-QMS) were applied for this purpose. The study includes a comparison of the results of tests conducted for polyamide recyclate, coal sludge, and PA6 recyclate composite with a filler constituting 5% of coal sludge.
PL
W pracy podjęto badania poznawcze nad możliwością wykorzystania odpadów poliamidowych PA6, charakteryzujących się wysoką kalorycznością. Zastosowano w tym celu techniki analizy termicznej (DSC/QMS). W pracy porównano wyniki badań przeprowadzonych dla recyklatu poliamidowego, mułu węglowego i kompozytu z recyklatu PA6 z napełniaczem stanowiącym 5% mułu węglowego.
PL
Przedstawiono krótką charakterystykę najczęściej stosowanych metod analizy termicznej oraz możliwości pomiarowych, jakie stwarzają poszczególne metody. Omówiono również wybrane właściwości fizykochemiczne azotanu(V) amonu oraz związane z nimi zagrożenia. Na podstawie dostępnej literatury dokonano oceny i klasyfikacji związków mających różny wpływ na rozkład termiczny azotanu(V) amonu. Związki te podzielono na substancje obojętne, promujące oraz inhibitujące rozkład termiczny azotanu(V) amonu.
EN
A review, with 39 refs., of the fundamentals of the most commonly used methods of thermal anal. (TG, DTA and DSC) and the measurement possibilities offered by each method. Selected phys. chem. properties of NH₄NO₃ and associated hazards were presented. Inorg. additives used or possible to be used in a mixt. with NH₄NO₃ and their effect on the course of exothermic decompn. were discussed. Mainly materials that can enrich NH₄NO₃ with nutrients, but also other inorg. salts as well as mine and waste raw materials, were considered.
first rewind previous Strona / 20 next fast forward last
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.