PL EN


Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
Tytuł artykułu

Multi-sensor evaluation of the concrete within the interlayer bond with regard to pull-off adhesion

Wybrane pełne teksty z tego czasopisma
Identyfikatory
Warianty tytułu
Języki publikacji
EN
Abstrakty
EN
The article presents the results of multi-sensor evaluation of the concrete within the interphase between overlay and existing substrate with regard to pull-off adhesion. It has been shown that both the effective surface area of the existing concrete substrate and the contribution of the exposed aggregate on this substrate, as a result of concrete substrate surface treatment, have a significant impact on pull-off adhesion. The highest adhesion was obtained when the surface of the existing concrete substrate was shot-blasted. This method of surface treatment provides both a high coarseness of the surface of the existing concrete substrate and considerable exposure of the aggregate on this surface. In order to clarify why this method of surface treatment of existing concrete substrate is advantageous with regard to the possibility of obtaining high adhesion, scanning electron microscopy (SEM) was used. SEM microstructural analysis was performed on concrete cubic specimens taken from the interphase zone between the overlay and existing concrete substrate. The results of these studies, including the contact type between the overlay made of cement mortar and the existing concrete substrate, are presented in the study.
Rocznik
Strony
573--582
Opis fizyczny
Bibliogr. 33 poz., rys., wykr.
Twórcy
autor
  • Faculty of Civil Engineering, Wrocław University of Science and Technology, Wybrzeże Wyspiańskiego 27, 50-370 Wroclaw, Poland, lukasz.sadowski@pwr.edu.pl
autor
  • Faculty of Mechanical Engineering, Wrocław University of Science and Technology, Wybrzeże Wyspiańskiego 27, 50-370 Wroclaw, Poland
autor
  • Faculty of Civil Engineering, Wrocław University of Science and Technology, Wybrzeże Wyspiańskiego 27, 50-370 Wroclaw, Poland
Bibliografia
  • [1] A. Rahman, C. Ai, C. Xin, X. Gao, Y. Lu, State-of-the-art review of interface bond testing devices for pavement layers: toward the standardization procedure, J. Adhes. Sci. Technol. 31 (2) (2017) 109–126.
  • [2] EN 1542, Products and systems for the protection and repair of concrete structures – test methods – measurement of bond strength by pull-off, 2006.
  • [3] ASTM D7234, Standard test method for pull-off adhesion strength of coatings on concrete using portable pull-off adhesion testers, 2005.
  • [4] L. Czarnecki, B. Chmielewska, Factors affecting adhesion in building joints, Cem. Wapno Beton 2 (2005) 74–85.
  • [5] L. Courard, Parametric study for the creation of the interface between concrete and repairs products, Mater. Struct. 33 (2000) 65–72.
  • [6] L. Sadowski, D. Stefaniuk, J. Hoła, L. Sadowski, D. Stefaniuk, J. Hoła, The effect of the porosity of concrete within the interfacial zone between layers on pull-off adhesion, Construct. Build. Mater. 152 (2017) 887–897.
  • [7] A. Garbacz, T. Piotrowski, L. Courard, L. Kwaśniewski, On the evaluation of interface quality in concrete repair system by means of impact-echo signal analysis, Construct. Build. Mater. 134 (2017) 311–323.
  • [8] A. Halicka, D. Franczak, Development of adhesion between two concretes during concrete hardening, Bud. Archit. 5 (2009) 5–16 (in Polish).
  • [9] P. Santos, E. Júlio, Factors affecting bond between new and old concrete, ACI Mater. J. 108 (4) (2011) 449–456.
  • [10] A. Garbacz, M. Górka, L. Courard, Effect of concrete surface treatment on adhesion in repair systems, Mag. Concrete Res. 57 (2005) 49–60.
  • [11] Ł. Sadowski, S. Czarnecki, J. Hoła, Evaluation of the height 3D roughness parameters of concrete substrate and the adhesion to epoxy resin, Int. J. Adhes. Adhes. 67 (2016) 3–13.
  • [12] J. Hoła, Ł. Sadowski, J. Reiner, S. Stach, Usefulness of 3D surface roughness parameters for nondestructive evaluation of pull-off adhesion of concrete layers, Construct. Build. Mater. 84 (2015) 111–120.
  • [13] C.M. Stolz, A.B. Masuero, D.T. Pagnussat, A.P. Kirchheim, Influence of substrate texture on the tensile and shear bond strength of rendering mortars, Construct. Build. Mater. 128 (2016) 298–307.
  • [14] ISO 25178, Geometrical Product Specification (GPS) – Surface Texture: Areal. Surface texture indications (Part 1); Terms, definitions and surface texture parameters.
  • [15] C.A. Brown, W.A. Johnsen, K.M. Hult, Scale-sensitivity, fractal analysis and simulations, Int. J. Mach. Tools Manuf. 38 (5) (1998) 633–637.
  • [16] C. Zanotti, N. Banthia, G. Plizzari, A study of some factors affecting bond in cementitious fiber reinforced repairs, Cem. Concr. Res. 63 (2014) 117–126.
  • [17] H. Beushausen, B. Höhlig, M. Talotti, The influence of substrate moisture preparation on bond strength of concrete overlays and the microstructure of the OTZ, Cem. Concr. Res. 92 (2017) 84–91.
  • [18] L. Courard, A. Darimont, Appetency and adhesion: analysis of the kinetics of contact between concrete and repairing mortars, Interfacial Zone Concr. (1998) 185–194.
  • [19] M. Lukovic, B. Šavija, H. Dong, E. Schlangen, G. Ye, Micromechanical study of the interface properties in concrete repair systems, J. Adv. Concr. Technol. 12 (2014) 320–339.
  • [20] M. Lukovic, G. Ye, Effect of moisture exchange on interface formation in the repair system studied by X-ray absorption, Materials 9 (2015).
  • [21] J.F. Maguire, P.L. Talley, M. Lupkowski, The interphase in adhesion: bridging the gap, J. Adhes. 45 (1–4) (1994) 269–290.
  • [22] S. Bouharoun, Characterization of the interface between fresh concrete and formwork, J. Civil Eng. Manage. 22 (1) (2016) 26–37.
  • [23] J. Rousseau, T.G. Mathia, Physique des solides et morphologie des surfaces, Acta Phys. Pol. A 5 (83) (1993).
  • [24] M. Kaszyńska, Early age properties of high-strength/high- performance concrete, Cem. Concr. Compos. 24 (2) (2002) 253–261.
  • [25] B. Bissonnette, L. Courard, A. Garbacz, Concrete Surface Engineering, CRC Press, 2015.
  • [26] Ł. Sadowski, D. Stefaniuk, Microstructural evolution within the interphase between hardening overlay and existing concrete substrates, Appl. Sci. 7 (2) (2017) 123.
  • [27] Ł. Sadowski, T.G. Mathia, Multi-scale metrology of concrete surface morphology: fundamentals and specificity, Construct. Build. Mater. 113 (2016) 613–621.
  • [28] M. Niemczewska-Wójcik, Multi-sensor measurements of titanium alloy surface texture formed at subsequent operations of precision machining process, Measurement 96 (2017) 8–17.
  • [29] R. Leach, Fundamental Principles of Engineering Nanometrology, Elsevier, 2014.
  • [30] P.J. de Groot, The meaning and measure of vertical resolution in optical surface topography measurement, Appl. Sci. 7–1 (2017) 54.
  • [31] B. Liu, T. Yang, Image analysis for detection of bugholes on concrete surface, Construct. Build. Mater. 137 (2017) 432–440.
  • [32] X. Pan, Z. Shi, C. Shi, T.C. Ling, N. Li, A review on concrete surface treatment. Part I: types and mechanisms, Construct. Build. Mater. 132 (2017) 578–590.
  • [33] S. Moon, J. Kim, J. Seo, Prototyping a remotely-controlled machine for concrete surface grinding operations, J. Civil Eng. Manage. 23 (2) (2016) 183–193.
Uwagi
PL
Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018)
Typ dokumentu
Bibliografia
Identyfikator YADDA
bwmeta1.element.baztech-f0a69160-1699-48e8-98e3-395cf2a603c3
JavaScript jest wyłączony w Twojej przeglądarce internetowej. Włącz go, a następnie odśwież stronę, aby móc w pełni z niej korzystać.