Narzędzia help

Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
first last
cannonical link button

http://yadda.icm.edu.pl:80/baztech/element/bwmeta1.element.baztech-b2fb8179-aa72-441d-9adb-3a2461970414

Czasopismo

Journal of Achievements in Materials and Manufacturing Engineering

Tytuł artykułu

Structure of EN AW-Al Cu4Mg1(A) composite materials reinforced with the Ti(C,N) ceramic particles

Autorzy Włodarczyk-Fligier, A.  Dobrzański, L. A.  Konieczny, J. 
Treść / Zawartość http://www.journalamme.org
Warianty tytułu
Języki publikacji EN
Abstrakty
EN Purpose: The purpose of the paper is to show and compare of modern method composite materials with aluminium alloy matrix reinforced by Ti(C,N) particles manufacturing. Design/methodology/approach: Powders of the starting materials were wet mixed in the laboratory vibratory ball mill to obtain the uniform distribution of the reinforcement particles in the matrix. The mixed powders were then dried in the air. The components were initially compacted at cold state in a die with the diameter of Ø 26 mm in the laboratory vertical unidirectional press - with a capacity of 350 kN. The selected compacting load was sufficient to obtain prepregs which would not crumble and at the same time would not be deformed too much, which would also have the adverse effect on their quality, as the excessive air pressure in the closed pores causes breaking the prepreg up when it is taken out from the die. The obtained PM compacts were heated to a temperature of 480-500°C and finally extruded - with the extrusion pressure of 500 kN. Findings: The received results show the possibility of obtaining the new composite materials with required structure joining positive properties composite materials components. Practical implications: Tested composite materials can be applied among the others in automotive industry but it requires additional researches. Originality/value: It was demonstrated structure of the extruded composite materials with the EN AW-Al Cu4Mg1(A) alloy matrix may be formed by the dispersion hardening with the Ti(C,N) particles in various portions and by the precipitation hardening of the matrix.
Słowa kluczowe
EN aluminium alloy   composite materials   powder metallurgy  
Wydawca International OCSCO World Press
Czasopismo Journal of Achievements in Materials and Manufacturing Engineering
Rocznik 2012
Tom Vol. 51, nr 1
Strony 22--29
Opis fizyczny Bibliogr. 34 poz., rys., tab.
Twórcy
autor Włodarczyk-Fligier, A.
  • Institute of Engineering Materials and Biomaterials, Silesian University of Technology, ul. Konarskiego 18a, 44-100 Gliwice, Poland, anna.wlodarczyk@polsl.pl
autor Dobrzański, L. A.
  • Institute of Engineering Materials and Biomaterials, Silesian University of Technology, ul. Konarskiego 18a, 44-100 Gliwice, Poland
autor Konieczny, J.
  • Institute of Engineering Materials and Biomaterials, Silesian University of Technology, ul. Konarskiego 18a, 44-100 Gliwice, Poland
Bibliografia
[1] B. Torres, H. Lieblich, J. Ibanez, A. Garcia-Escorial, Mechanical properties of some PM aluminide and silicide reinforced 2124 aluminium matrix composites, Scripta Materialia 47/1 (2002) 45-49.
[2] A. Jimenez-Morales, E.M. Ruiz-Navas, J.B. Fogagnolo, J.M. Torralba, Corrosion resistance of 6061 aluminium base composite materials, Advances in Materials and Processing Technologies (2003) 1267-1270.
[3] S.C. Tjong, Z.Y. Mal, Microstructural and mechanical characteristics of in situ metal matrix composites, Materials Science and Engineering 29 (2000) 49-113.
[4] M. Dyzia, J. Śleziona, Aluminium matrix composites reinforced with AlN particles formed by in situ reaction, Archives of Materials Science and Engineering 31/1 (2008) 17-20.
[5] G.E. Kiourtsidis, S.M. Skolianos, E.G. Pavlidou, A study on pitting behaviour of AA2024/SiCp composites using the double cycle polarization technique, Corrosion Science 41 (1999) 1185-1203.
[6] J.-W. Yeh, S.-Y. Yuan, Ch.-H. Peng, A reciprocating extrusion process for producing hypereutectic Al - 20 wt. % Si wrought alloys, Materials Science and Engineering A 252 (1998) 212-216.
[7] M. Rahimian, N. Ehsani N. Parvin, H. Baharvandi, The effect of particle size, sintering temperature and sintering time on the properties of Al-Al2O3 composites, made by powder metallurgy, Journal of Materials Processing Technology 209 (2009) 5387-5393.
[8] A. Włodarczyk-Fligier, L.A. Dobrzański, M. Adamiak, Influence of heat treatment on properties and corrosion resistance of Al-composite, Journal of Achievements in Materials and Manufacturing Engineering 21/1 (2007) 55-58.
[9] L.A. Dobrzański, A. Włodarczyk, M. Adamiak, Composite materials based on EN AW-Al Cu4Mg1(A) aluminium alloy reinforced with the Ti(C,N) ceramic particles, Materials Science Forum 530-531 (2006) 243-248.
[10] L.A Dobrzański, A. Włodarczyk-Fligier, Matrix composite materials reinforced by ceramic particles, Proceedings of the 17th International Scientific Conference “Contemporary Achievements in Mechanics, Manufacturing and Materials Science” CAM3S’2011, Gliwice-Wrocław, 2011, 46 (in Polish).
[11] G.G. Kang, Y.H. Seo, The influence of fabrication parameters on the deformation behavior of the perform of metal-matrix composites during the squeeze-casting processes, Journal of Materials Processing Technology 61 (1996) 241-249.
[12] H.S. Chu, K.S. Liu, J.W. Yeh, Aging behavior and tensile properties of 6061Al203p μm Al2O3p particle composites produced by reciprocating extrusion, Scripta Materialia 45 (2001) 541-546.
[13] J.M. Torralba, C.E. Costa, F. Velasco, P/M aluminium matrix composites: an overview, Journal of Materials Processing Technology 133 (2003) 203-206.
[14] S.I. Hong, Y.S. Seo, Effect of microstructure on wear behavior of Al-Mg-Si alloy matrix-10 vol.% Al2O3 composite, Materials Science and Engineering A 265 (1999) 29-41.
[15] Y.T. Kim, K. Ikeda, T. Murakami, Metal flow in porthole die extrusion of aluminium, Journal of Materials Processing Technology 121 (2002) 107-115.
[16] P.B. Silna-Maia, F. Velasco. N. Anton, C.E. Costa, W.C Zapata, Corrosion resistance of 2014 aluminium matrix composites reinforced with atomised Ni3Al, Advanced Performance Materials 6 (1999) 117-121.
[17] A. Kostka, J. Lelątko, M. Gigla H. Morawiec, A. Janas, Structure of interface in Al-TiB2 composite studied by TEM, Composites 2 (2002) 297-302.
[18] M. Dyzia, J. Śleziona, Aluminium matrix composites reinforced with AlN particles formed by in situ reaction, Archives of Materials Science and Engineering 31/1 (2008) 17-20.
[19] S.C. Tjong, Z.Y. Mal, Microstructural and mechanical characteristics of in situ metal matrix composites, Materials Science and Engineering 29 (2000) 49-113.
[20] M. Rahimian, N. Parvin, N. Ehsani, The effect of production parameters on microstructure and wear resistance of powder metallurgy Al-Al2O3 composite, Materials and Design 32 (2011) 1031-1038.
[21] L.A. Dobrzański, A. Włodarczyk, M. Adamiak, Structure and properties of PM composite materials based on EN AW-2124 aluminum alloy reinforced with the BN or Al2O3 ceramics particles, Journal of Materials Processing Technology 175/1-3 (2006) 186-191.
[22] H. Morawiec, A. Kostka, J. Lelątko, M. Gigla, A. Janas, Structure of interface in Al-TiC composite, Composites 1 (2001) 228-232.
[23] M. Adamiak, J.B. Fogagnolo, E.M. Ruiz-Navas, L.A. Dobrzański, J.M. Torralba, Mechanically milled MMC reinforced with intermetallics- the structure and properties, Proceedings of the International AMPT Conference, Dublin, Ireland, 2003, 1448.
[24] S.I. Hong, Y.S. Seo, Effect of microstructure on wear behavior of Al-Mg-Si alloy matrix-10 vol.% Al2O3 composite, Materials Science and Engineering A 265 (1999) 29-41.
[25] Y.T. Kim, K. Ikeda, T. Murakami, Metal flow in porthole die extrusion of aluminium, Journal of Materials Processing Technology 121 (2002) 107-115.
[26] P.B. Silna-Maia, F. Velasco. N. Anton, C.E. Costa, W.C. Zapata, Corrosion resistance of 2014 aluminium matrix composites reinforced with atomised Ni3Al, Advanced Performance Materials 6 (1999) 117-127.
[27] S.C. Tjong, Z.Y. Mal, Microstructural and mechanical characteristics of in situ metal matrix composites, Materials Science and Engineering 29 (2000) 49-113.
[28] M. Dyzia, J. Śleziona, Aluminium matrix composites reinforced with AlN particles formed by in situ reaction, Archives of Materials Science and Engineering 31/1 (2008) 17-20.
[29] L.A. Dobrzański, A. Włodarczyk-Fligier, M. Adamiak, The influence of heat treatment on corrosion resistance of PM composite materials based on EN AW-Al Cu4Mg1 (A) aluminum alloy reinforced with the Ti(C,N) particles, Materials Science Forum 534-536 (2007) 845-848.
[30] G.E. Kiourtsidis, S.M. Skolianos, E.G. Pavlidou, A study on pitting behaviour of AA2024/SiCp composites using the double cycle polarization technique, Corrosion Science 41 (1999) 1185-1203.
[31] A. Włodarczyk-Fligier, L.A. Dobrzański, M. Kremzer, M. Adamiak, Manufacturing of aluminium matrix composite materials reinforced by Al2O3 particles, Journal of Achievements in Materials and Manufacturing Engineering 27/1 (2008) 99-102.
[32] L.A. Dobrzański, A. Włodarczyk-Fligier, M. Adamiak, Properties and corrosion resistance of PM composite materials based on EN AW-Al Cu4Mg1(A) aluminum alloy reinforced with the Ti(C,N) particles, Proceedings of the 11th International Scientific Conference “Contemporary Achievements in Mechanics, Manufacturing and Materials Science” CAM3S'2005, Gliwice-Zakopane, 2005, 289-295.
[33] L.A. Dobrzański, J. Konieczny, Effect of extrusion parameters on the heterogeneity of the structure and condition of the surface layer of aluminum profiles, Proceedings of the Scientific Conference “Materials, Mechanical and Manu-facturing Engineering” M3E'2000, Gliwice, 2000, 63-66 (in Polish).
[34] PN-EN 573-3, Aluminium and aluminium alloys-Chemical compositions and plastic formed product types, 1998.
Kolekcja BazTech
Identyfikator YADDA bwmeta1.element.baztech-b2fb8179-aa72-441d-9adb-3a2461970414
Identyfikatory