Narzędzia help

Preferencje help
Widoczny [Schowaj] Abstrakt
Liczba wyników
first last
cannonical link button

http://yadda.icm.edu.pl:80/baztech/element/bwmeta1.element.baztech-0976836d-3afb-4334-91a6-96c769277c53

Czasopismo

Advances in Science and Technology Research Journal

Tytuł artykułu

Mechanical properties of hand-making polyester composites

Autorzy Rudawska, Anna  Malczarski, Mateusz  Stančeková, Dana  Wahab, Magd Abdel  Schindlerová, Vladimira 
Treść / Zawartość
Warianty tytułu
Języki publikacji EN
Abstrakty
EN The aim of this paper is to determine the effect of arrangement of fibreglass fabric plies in a polymer composite on a strength. Based on the experimental results, the real effect of plies arrangement and their most favourable configuration with respect to strength is determined. The experiments were performed on 4 types of handmade composites which had different fibre orientations and thicknesses. The first three of the composites had three plies of fabric. The plies arrangement in Composite I was unchanged, in Composite II the central ply had the 45o orientation, while in Composite III the outside ply (tangential to the adhesive layer) was oriented at 45o. In contrast, Composite IV consisted of five plies with unchanged arrangement. Composite plates were first cut into smaller specimens and then after stabilizing, the composite specimens were subjected to strength tests. The highest tensile strength and elongation are obtained for Composite IV, which was the higher the thickness from the tested composite samples, but for this composite the tensile modulus was lowest value. Composite II has the lowest values of strength parameters among the tested composites, which contain three plies and central ply has the 45o orientation.
Słowa kluczowe
PL kompozyty polimerowe   orientacja warstwowa   siła  
EN polymer composites   plies orientation   strength  
Wydawca Oddział SIMP w Lublinie
Czasopismo Advances in Science and Technology Research Journal
Rocznik 2018
Tom Vol. 12, no 2
Strony 112--120
Opis fizyczny Bibliogr. 37 poz., fig., tab.
Twórcy
autor Rudawska, Anna
  • Lublin University of Technology, Faculty of Mechanical Engineering, ul. Nadbystrzycka 36, 20-618 Lublin, Poland, a.rudawska@pollub.pl
autor Malczarski, Mateusz
  • Lublin University of Technology, Faculty of Mechanical Engineering, ul. Nadbystrzycka 36, 20-618 Lublin, Poland, malczarski@gmail.com
autor Stančeková, Dana
autor Wahab, Magd Abdel
  • Ghent University, Faculty of Engineering and Architecture, Technologiepark Zwijnaarde 903, B-9052 Zwijnaarde, Belgium, Magd.AbdelWahab@UGent.be
autor Schindlerová, Vladimira
  • Technical University of Ostrava, Faculty of Mechanical Engineering, 17.listopadu 15, 708 33 Ostrava – Poruba, Czech Republic, vladimira.schindlerova@vsb.cz
Bibliografia
1. Adams R.D. (ed.). Adhesive bonding. Science, technology and applications. Woodhead Publishing, United Kingdom, 2010.
2. Baley C., Davies P., Grohens Y. and Dolto G. Application of interlaminar tests to marine composites - a literature review. Applied Composite Materials, 11, 2004, 99–126.
3. Bénard Q., Fois,M. and Grisel M. Influence of fibre reinforcement and peel ply surface treatment towards adhesion of composite surfaces. International Journal of Adhesion and Adhesives, 25, 2005, 404–409.
4. Boczkowska A., Kapuściński J., Lindemann Z., Witembeg-Perzyk D. and Wojciechowski S. Kom-pozyty. Oficyna Wydawnicza Politechniki Warszawskiej, Warszawa, 2003.
5. Brandt A.M. Fibre reinforced cement-based (FRC) composites after over 40 years of development in building and civil engineering. Composite Structures, 86, 2008, 3–9.
6. Centea, T. Grunenfelder L.K. and Nutt S.R. A review of out-of-autoclave prepregs – material properties, process phenomena, and manufacturing considerations. Composites Part A: Applied Science and Manufacturing, 70, 2015, 132–154.
7. Chand S. Carbon fibers for composites. Journal of Materials Science, 35, 2000, 1303–1313.
8. Czub P., Bończa-Tomaszewski Z. Penczek P. and Pielichowski J. Chemia i technologia żywic epok-sydowych. WNT, Warszawa, 2002.
9. de Ulzurrun I.D., López F., Herreros M.A. and Suárez J.C. Tests of deck-to-hull adhesive joints in GFRP boats. Engineering Failure Analysis, 14, 2007, 310–320.
10. Ferdous W., Manalo A., Van Erp G., Aravinthan T., Kaewunruen S. and Remennikov A. Composite railway sleepers: recent developments, challenges and future prospects. Composite Structures, 134, 2015, 158–168.
11. Friedrich K., Zhang Z. and Schlarb A.K. Effects of various fillers on the sliding wear of polymer composites. Composites Science and Technology, 65, 2005, 2329–2343.
12. Grin I. Materiały polimerowe. PWN, Warszawa, 2003.
13. Hatta H., Koyama M., Bando T., Kogo Y., Fukusa H. and Ishida H. The effects of processing variables on strength of carbon bonding between carbon/carbon composites. Materials Science Engineering A, 513–514, 2009, 138–144.
14. http://www.ciechgroup.com (access on 14-03-2017).
15. http://www.krisko.lublin.pl (access on 12-03-2017).
16. Katnam K.B., Comer A.J., Stanley W.F., Buggy M., Ellingboe A.R. and Young T.M. Characterising pre-preg and non-crimp-fabric composite single lap bonded joints. International Journal of Adhesion and Adhesive, 31, 2011, 679–686.
17. Kaye R. and Heller M. Finite element-based three-dimensional stress analysis of composite bonded repairs to metallic aircraft structure. International Journal of Adhesion and Adhesives, 26, 2006, 261–273.
18. Khandan R., Noroozi S., Sewell P. and Vinney J. The development of laminated composite plate theories: a review. Journal of Materials Science, 47, 2012, 5901–5910.
19. Kim S.S. and Lee D.G. Design of the hybrid composite journal bearing assembled by interference fit. Composite Structure, 75, 2006, 222–230.
20. Królikowski W., Kłosowska-Wołkowicz Z. and Penczek P. Żywice i laminaty poliestrowe. WNT, Warszawa, 2002.
21. Kumar P., Singh R.K. and Kumar R. Joining similar and dissimilar materials with GFRP. International Journal of Adhesion and Adhesives, 27, 2007, 68–76.
22. Lee J. and Drzal L.T. Surface characterization and adhesion of carbon fibers to epoxy and polycarbon-ate. International Journal of Adhesion and Adhesives, 25, 2005, 389–394.
23. Minnetyan L. and Chamis C.C. Progressive fracture of adhesively bonded composite structures. Theoretical Applied Fracture Mechanics, 31, 1999, 75–84.
24. Mouritz A.P., Bannister M.K., Falzon P.J. and Leong K.H. Review of applications for advanced three-dimensional fibre textile composites. Composites Part A, 30, 1999, 1445–461.
25. Oueiny C., Berlioz S. and Perrin, F.-X. Carbon nanotube–polyaniline composites. Progress in Polymer Science, 39, 2014, 707–748.
26. Pang H., Xu L., Yan D.-X. and Li Z.-M. Conductive polymer composites with segregated structures. Progress in Polymer Science, 39, 2014, 1908–1933.
27. Parashar A. and Mertiny P. Adhesively bonded composite tubular joints: Review. International Journal of Adhesion and Adhesives, 38, 2012, 58–68.
28. Rodrigues D.D. and Broughton J.G. Silane surface modification of boron carbide in epoxy composites. International Journal of Adhesion and Adhesives, 46, 2013, 62–73.
29. Rudawska A. Selected aspects of FEM analysis for bonded joints of polymer composite materials. Journal of Physics: Conference Series 628, 2015, 012077.
30. Sabu T., Kuruvilla J., Malhotra S.K., Koichi G. and Sreekala M.S. Polymer Composites, Volume 2: Nanocomposites. Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim, Germany, 2013.
31. Sengupta R., Bhattacharya M., Bandyopadhyay S. and Bhowmick A.K. A review on the mechanical and electrical properties of graphite and modified graphite reinforced polymer composites. Progress in Polymer Science, 36, 2011, 638–670.
32. Wahab M.A., Ashcroft I.A., Crocombe A.D., and Smith P.A. Finite element prediction of fatigue crack propagation lifetime in composite bonded joint, Composites A, 35, 2004, 213–222.
33. Wahab M.A.Joining composites with adhesives. DEStech Publications, Inc, Lancaster, 2016.
34. Wang C., Huang Y. D. and Wang B. Study on heat-resistant property of adhesive/carbon-carbon com-posite joints. International Journal of Adhesion and Adhesives, 26, 2006, 206–211.
35. Yan L., Kasal B. and Huang L. A review of recent research on the use of cellulosic fibres, their fibre fabric reinforced cementitious, geo-polymer and polymer composites in civil engineering. Composites Part B: Engineering, 92, 2016, 94–132.
36. Zhu J., Zhu H., Njuguna J. and Abhyankar H. Recent development of flax fibres and their reinforced composites based on different polymeric matrices. Materials, 6, 2013, 5171–5198.
37. Żuchowska D. Polimery konstrukcyjne. WNT, Warszawa, 2000.
Uwagi
Opracowanie rekordu w ramach umowy 509/P-DUN/2018 ze środków MNiSW przeznaczonych na działalność upowszechniającą naukę (2018).
Kolekcja BazTech
Identyfikator YADDA bwmeta1.element.baztech-0976836d-3afb-4334-91a6-96c769277c53
Identyfikatory
DOI 10.12913/22998624/91891